Please note that our Terms & Conditions and Privacy Notice are applicable.
On Promotion in Home & Garden
Pay & Ship
Buy with confidence. Secure payment options & nationwide delivery. Learn more
Filter & refine
Clear All
Results for Tanks & Water Storage Tanks in Mbombela / Nelspruit in Mbombela / Nelspruit
1
R 605.48
SavedSave
Please note that shipping and installation is not included.
Firstly the Domestic plastic water meter – pulse ready – 20mm.
Measurement of volume of cold potable water consumption. Also suitable
for both domestic and small business applications.
FEATURES
Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering.
Installation Instructions
Thank you for purchasing this high-quality Domestic plastic water meter – pulse ready – 20mm. As a matter of fact the steps below will guide you through the proper
installation process for your Polymer Piston Water Meter to ensure top
performance and compliance with warranty conditions provided by The
Water Company.
Step 1: Protecting the Meter
Start by ensuring all plastic water meters are covered post
installation. This protects the meter from direct sunlight, which can be
done using a housing or meter box.
Step 2: Sizing
Make sure the water meter is correctly sized according to the pipe size or the flow rate.
Step 3: Flushing Pipework
Before installation:
Flush all pipework to remove debris or sand, ensuring a clean pipeline.
Step 4: Meter Orientation
Install piston meters either horizontally or vertically.
Step 5: Avoiding Pressure
Ensure no pressure is applied to the meter during installation from
misaligned pipes or excessive vibration, which can lead to failure.
Step 6: Fitting Installation
Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks.
Step 7: Thread Treatment
Only use thread tape or PTFE tape, ideally with tailpieces.
Step 8: Soldering Precautions
Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat.
Step 9: Water Type
Ensure the meter installed for cold water is not used in a hot water pipeline.
Step 10: Appropriate Usage
Use the meter only for clean potable water to avoid damage and inaccuracies.
Step 11: Handling Care
Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal.
Step 12: Thread Fittings
Avoid using tapered thread fittings; Use of tailpieces is preferable.
Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from sand or foreign debris.
1mo
Mbombela / Nelspruit
1
R 521.64
SavedSave
Please note that shipping and installation is not included.
Firstly the Domestic plastic water meter – pulse ready – 20mm.
Measurement of volume of cold potable water consumption. Suitable for
both domestic and small business applications.
FEATURES
Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering.
Installation Instructions
Thank you for purchasing this high-quality Polymer Piston Domestic Water Meter. The steps below will guide you through the proper installation
process for your Polymer Piston Water Meter to ensure top performance
and compliance with warranty conditions provided by The Water Company.
Step 1: Protecting the Meter
Firstly start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box.
Step 2: Sizing
Secondly make sure the water meter is correctly sized according to the pipe size or the flow rate.
Step 3: Flushing Pipework
Before installation:
Flush all pipework to remove debris or sand, ensuring a clean pipeline.
Step 4: Meter Orientation
Install piston meters either horizontally or vertically.
Step 5: Avoiding Pressure
Ensure no pressure is applied to the meter during installation from
misaligned pipes or excessive vibration, which can lead to failure.
Step 6: Fitting Installation
Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks.
Step 7: Thread Treatment
Only use thread tape or PTFE tape, ideally with tailpieces.
Step 8: Soldering Precautions
Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat.
Step 9: Water Type
Ensure the meter installed for cold water is not used in a hot water pipeline.
Step 10: Appropriate Usage
Use the meter only for clean potable water to avoid damage and inaccuracies.
Step 11: Handling Care
Handle the meter carefully as it is a precision measuring instrument.
Do not drop it or break the meter seal.
Step 12: Thread Fittings
Avoid using tapered thread fittings; Use of tailpieces is preferable.
Step 13: Additional Protection
Install a strainer before the water meter to protect it from sand or foreign debris.
1mo
Mbombela / Nelspruit
1
R 2,926.46
SavedSave
Please note that shipping and installation is not included.
Domestic brass water meter – CL C pulse ready – 25mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly the Domestic brass water meter – CL C pulse ready – 25mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. As a result should the water temperature
at the metering point exceed this, this meter will be damaged
irreparably. Do not solder capillary-type fittings while fitted to the
meter or use heat while this meter is fitted in the pipeline. Heat
travels through the pipe during this process and this will damage the
internals of the water meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.
Another key point precautions must be taken to prevent freezing. All
things considered a meter will be damaged and could even burst if the
water freezes. The meter should also be installed at least one meter
away from any freezing point like a standpipe for example where the
water can freeze back down the pipeline from that point.
1mo
Mbombela / Nelspruit
1
R 1,218.71
SavedSave
Please note that shipping and installation is not included.
The Domestic brass water meter – CL C pulse ready – 20mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly this Domestic brass water meter – CL C pulse ready – 20mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. Should the water temperature at the
metering point exceed this, this meter will be damaged irreparably. Do
not solder capillary-type fittings while fitted to the meter or use heat
while this meter is fitted in the pipeline. Heat travels through the
pipe during this process and this will damage the internals of the water
meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. A
meter will be damaged and could even burst if the water freezes. The
meter should also be installed at least one meter away from any freezing
point like a standpipe for example where the water can freeze back down
the pipeline from that point.
1mo
Mbombela / Nelspruit
1
R 1,102.27
SavedSave
Please note that shipping and installation is not included.
The Domestic brass water meter – CL C pulse ready – 15mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly the Domestic brass water meter – CL C pulse ready – 15mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. As a result should the water temperature
at the metering point exceed this, this meter will be damaged
irreparably. Do not solder capillary-type fittings while fitted to the
meter or use heat while this meter is fitted in the pipeline. Heat
travels through the pipe during this process and this will damage the
internals of the water meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. All
things considered a meter will be damaged and could even burst if the
water freezes. The meter should also be installed at least one meter
away from any freezing point like a standpipe for example where the
water can freeze back down the pipeline from that point.
1mo
Mbombela / Nelspruit
1
Contact f/price
SavedSave
Please note that shipping and installation is not included.The new DAB Nova submersible pump 0.25kW were redesigned to mark the
occasion of forty years on the market and to make them even more
reliable, robust and ergonomic.
As has been noted high performance. NOVA and FEKA have professional
features such as the oil chamber triple seal and lubricated bearings.
Being that better protection against corrosion Motor in AISI 304
stainless steel and shaft in AISI 431 steel for better protection
against corrosion.
Technical Data
Operating range:
Flow rate up to 16 m3/h with head up to 10.2 meters
Liquid temperature range:
From 0 °C to +35 °C for domestic use. From 0 °C to +50 °C for other uses.
Output
1.1/4″ F
Pumped liquid:
Cesspool sewage water.
Max. immersion depth: 7 meters.
Maximum dry run time: 1 minute.
Protection class: IP 68.
Insulation class: F.
Free Passage: 10 mm
Most important the DAB Nova submersible pump 0.25kW line with open
impeller is suited to all clean and waste water with solids measuring up
to 10 mm. It can be used to empty tanks, vats or cisterns, drain
flooded basements, cellars and garages, and prevent flooding when
installed in rainwater wells.It can also be used as a portable pump in emergencies to drain water
out of flooded rooms. They can also be used for emptying tanks or
cisterns. The pumps are suitable for drainage of flooded basements,
cellars and garages or to prevent flooding when installed in rainwater
collector wells, which can also be used as a portable pump in emergency
situations to drain water from flooded premises.
1mo
Mbombela / Nelspruit
1
R 2,986
SavedSave
Please note that shipping and installation is not included.The new DAB Nova submersible pump 0.20kW were redesigned to mark the
occasion of forty years on the market and to make them even more
reliable, robust and ergonomic.
As has been noted high performance. NOVA and FEKA have professional
features such as the oil chamber triple seal and lubricated bearings.
Being that better protection against corrosion Motor in AISI 304
stainless steel and shaft in AISI 431 steel for better protection
against corrosion.
Technical Data
Operating range:
Flow rate up to 16 m3/h with head up to 10.2 meters
Liquid temperature range:
From 0 °C to +35 °C for domestic use. From 0 °C to +50 °C for other uses.
Output
1.1/4″ F
Pumped liquid:
Cesspool sewage water.
Max. immersion depth: 7 meters.
Maximum dry run time: 1 minute.
Protection class: IP 68.
Insulation class: F.
Free Passage: 5mm
Most important the DAB Nova submersible pump 0.20kW line with open
impeller is suited to all clean and waste water with solids measuring up
to 10 mm. It can be used to empty tanks, vats or cisterns, drain
flooded basements, cellars and garages, and prevent flooding when
installed in rainwater wells.
It can also be used as a portable pump in emergencies to drain water
out of flooded rooms. They can also be used for emptying tanks or
cisterns. The pumps are suitable for drainage of flooded basements,
cellars and garages or to prevent flooding when installed in rainwater
collector wells, which can also be used as a portable pump in emergency
situations to drain water from flooded premises.
1mo
Mbombela / Nelspruit
1
R 4,690
SavedSave
Please note that shipping and installation is not included.The new DAB Feka submersible pump 0.55kW were redesigned to mark the
occasion of forty years on the market and to make them even more
reliable, robust and ergonomic.
The submersible pump of the FEKA series is suitable for lifting
sewage water from cesspools, and is capable of handling suspended solid
matter with size up to 25 mm.
As has been noted high performance. NOVA and FEKA have professional
features such as the oil chamber triple seal and lubricated bearings.
Being that better protection against corrosion Motor in AISI 304
stainless steel and shaft in AISI 431 steel for better protection
against corrosion.
Technical Data
Operating range:
Flow rate up to 16 m3/h with head up to 7.5 meters
Liquid temperature range:
From 0 °C to +35 °C for domestic use. From 0 °C to +50 °C for other uses.
Output
1.1/4″ F
Pumped liquid:
Cesspool sewage water.
Max. immersion depth: 7 meters.
Maximum dry run time: 1 minute.
Protection class: IP 68.
Insulation class: F.
Free Passage: 25 mm
Most important the DAB Feka submersible pump 0.55kW with back flowing
impeller is suited to all clean and waste water loaded with solids
measuring up to 25 mm.It can be used to empty tanks, vats or cisterns,
drain flooded basements, cellars and garages, and prevent flooding when
installed in rainwater wells.It can also be used as a portable pump in
emergencies to drain water out of flooded rooms where there is mud or
detritus.
Domestic waste waterRainwater or groundwaterEmptying of wells or collection tanksEmptying of swimming pools or rooms prone to flooding
1mo
Mbombela / Nelspruit
1
R 36,071
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 2.2kW three phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 2.2kW three phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motor
Single-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C. Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
1mo
Mbombela / Nelspruit
1
R 30,389
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 1.1kW three phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 1.1kW three phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motor
Single-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C. Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
1mo
Mbombela / Nelspruit
1
R 28,495
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 0.7kW single phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 0.7kW single phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 \ ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motorSingle-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C. Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
1mo
Mbombela / Nelspruit
1
R 10,539
SavedSave
Please note that shipping and installation is not included.Firstly Feka vs submersible pumps 0.75kW – three phase with micro
cast steel liquid vortex impeller, suitable for lifting sewage and drain
water in general containing solid matter with size up to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.75kW – three phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 3 x 400 V
Installation: Fixed or portable, vertical position
Input Voltage A: 1.94
Output Voltage A: 11HP: 1
1mo
Mbombela / Nelspruit
1
R 8,352
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel DAB Feka vs submersible pumps 0.55kW – three
phase with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.55kW – three phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 3 x 400 V ~
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 1.64
Output Voltage A: 11HP: 0.75
1mo
Mbombela / Nelspruit
1
R 11,779
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 1kW – single phase
with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina.
DAB Feka vs submersible pumps 1kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 6.63
Output Voltage A: 31HP: 1.36
1mo
Mbombela / Nelspruit
1
R 12,089
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 1.2kW – single
phase with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 1.2kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 8.63
Output Voltage A: 38HP: 1.6
1mo
Mbombela / Nelspruit
1
R 9,740.99
SavedSave
Please note that shipping and installation is not included.Firstly Feka vs submersible pumps 0.75kW – single phase with micro
cast steel liquid vortex impeller, suitable for lifting sewage and drain
water in general containing solid matter with size up to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.75kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Input Voltage A: 5.13
Output Voltage A: 20HP: 1
1mo
Mbombela / Nelspruit
1
R 9,850
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 0.75kW – single
phase with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.75kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 5.13
Output Voltage A: 20HP: 1
1mo
Mbombela / Nelspruit
1
R 14,582
SavedSave
Please note that shipping and installation is not included.First thing to remember the Feka VS submersible grinder pump 1kW is a
single-stage submersible pump. Incorporating an AISI 630 stainless
steel shredder, designed for transferring untreated wastewater
containing stringy material.
It is suited to settings where a high head is required. Such as in
the case of pipework with a small diameter or where connection to the
public sewer is some distance away. Or when wanting to avoid the risk of
clogging. In addition, with its small footprint and both flanged and
threaded outlet ports, Feka VS Grinder is ideal as a replacement in
existing or outdated systems.
This is further testament to how DAB is attuned to the needs of all
market players, from the installer to the end user. Feka vs submersible
grinder pump 1kW is specifically sized to fully meet the functional,
performance and consumption requirements of the specific applications
for which it has been designed, ensuring maximum performance levels
without wasting energy and economic resources.
Finally wear-resistant materials, such as cast iron and stainless
steel, and performance capable of achieving heads of up to 25 meters,
come together to ensure an increasingly rewarding installation and user
experience, and a longer pump life
Technical Data
Flow rate: From 0 m3h to 14,4 m3hHead: 25 mPumped liquid: Sewage water, gray waterFree passage: N/ALiquid temperature: From 0°C to +40°C for domestic useOutlet: 1’’ 1/2 GAS – DN 32 and DN 40Outlet direction: Horizontal and vertical with curve kit accessoryImpeller: Vortex in cast iron, there is a shredderMotor protection degree: IP 68Thermal classification of the motor insulation: FPower cable type: H07RN8-FPossible type of installation: fixed or mobile in vertical positionMaximum immersion depth: 7 meters
1mo
Mbombela / Nelspruit
1
R 24,992
SavedSave
Please note that shipping and installation is not included.Firstly the DAB Feka FXV submersible pumps 1.1kW – single phase is a
submersible pump for draining sewage water in commercial building
service. It is certified for the European Union standard EN 12050-1
which applies to sewage lifting containing faecal material in buildings
and construction sites. Pump suitable for fixed installations with a
coupling device or mobile if placed directly on the bottom of the tank.
High-performance super vortex impeller with solid handling up to 50
mm or 60 mm. The DAB Feka FXV submersible pumps 1.1kW – single phase is
suitable for liquid with solids and long fibers in suspension. The
reduced overall dimensions and the outlet ports both flanged and
threaded make it ideal for replacements.
Designed for quick maintenance thanks to a constructive solution that
provides easy access to the main components of the pump. Automatic
versions with power up to 1,5 kW. ATEX version available for use in
potentially explosive environments. (ATEX certifications: II2G Ex db k
IIB T4 or IEC EX: Ex db IIB T4 Gb).
Technical Data
Flow rate minimum and maximum: 62,8 m3/h
Head up to: 19,6 m
Immersion dept (maximum): 20 m
Type of pumped liquid: Waters with filamentary bodies, paper or textile material in the presence of domestic or civil waste.
Free passage: 50 mm or 65 mm depending on the model
Supported liquid temperature (maximum and minimum): + 50°C (+ 60°C for a short period of time)
Flange and threaded: From 2″, DN50, DN65
Impeller type: Vortex
Start time (maximum) per hour: 20/h
Class of protection: IP 68
Motor insulation class: F
Single phase power input: 1x 220-240V 50Hz
Three phase power input: 3x 400V 50Hz / 3x 230V 50Hz only on request
Maximum dry run time: 10 min
Power cable (m) and plug: 10 m
Possible type of installation: mobile when on the ground, fixed with coupling
Certification: EN 12050-1 \ ATEX
Special versions on request: different cable lengths, different voltages and frequencies
1mo
Mbombela / Nelspruit
1
R 27,226
SavedSave
Please note that shipping and installation is not included.Firstly the DAB Feka FXV submersible pumps 0.7kW – single phase is a
submersible pump for draining sewage water in commercial building
service. It is certified for the European Union standard EN 12050-1
which applies to sewage lifting containing faecal material in buildings
and construction sites. Pump suitable for fixed installations with a
coupling device or mobile if placed directly on the bottom of the tank.
High-performance super vortex impeller with solid handling up to 50
mm or 60 mm. The DAB Feka FXV submersible pumps 0.7kW – single phase is
suitable for liquid with solids and long fibers in suspension. The
reduced overall dimensions and the outlet ports both flanged and
threaded make it ideal for replacements.
Designed for quick maintenance thanks to a constructive solution that provides easy access to the main components of the pump. Automatic
versions with power up to 1,5 kW. ATEX version available for use in
potentially explosive environments. (ATEX certifications: II2G Ex db k
IIB T4 or IEC EX: Ex db IIB T4 Gb).
Technical Data
Flow rate minimum and maximum: 62,8 m3/h
Head up to: 19,6 m
Immersion dept (maximum): 20 m
Type of pumped liquid: Waters with filamentary bodies, paper or textile material in the presence of domestic or civil waste.
Free passage: 50 mm or 65 mm depending on the model
Supported liquid temperature (maximum and minimum): + 50°C (+ 60°C for a short period of time)
Flange and threaded: From 2″, DN50, DN65
Impeller type: Vortex
Start time (maximum) per hour: 20/h
Class of protection: IP 68
Motor insulation class: F
Single phase power input: 1x 220-240V 50Hz
Three phase power input: 3x 400V 50Hz / 3x 230V 50Hz only on request
Maximum dry run time: 10 min
Power cable (m) and plug: 10 m
Possible type of installation: mobile when on the ground, fixed with coupling
Certification: EN 12050-1 ATEX
Special versions on request: different cable lengths, different voltages and frequencies
1mo
Mbombela / NelspruitSave this search and get notified
when new items are posted!