Please note that our Terms & Conditions and Privacy Notice are applicable.
Bernard Pollet
Selling for 17+ years
Total Ads150
Active Ads12
Seller stats
150Total Ads
52.04KTotal Views
Verified information
This indicates that Gumtree has taken reasonable steps to verify the authenticity of the Seller’s profile.
Read More
Read More
Mobile number
Email address
12 Active Ads
2
New Subaru Forester 2.5 lambda sensor from agents. This is the downstream unit. Excludes R100 for courier fees
3mo
Pay & Ship
2
4 bushes with 1 centre metal bush and 1 bolt with nut and washer.
Removing the bushes without a press is challenging, but, the new bushes press in quite easily by hand. To remove the arm is quite challenging and involves dropping the fuel tank. I have included the bolt as I found it easier to cut off the bolt with an angle grinder and NOT drop the fuel tank.
This add is not for the arm, and only for the replacement bushes as pictured. I have personally fitted them to my car with positive results. Only 1 centre metal bush is provided as the other is reusable from the old bush and saves on cost. I can include both centre metal bushes on request.
The price excludes courier fees.
1y
2
The original specification rubber control arm bushes for Mitsubishi Pajero gen3. These bushes are press fitted. Sold as a set (4) bushes. Price excludes courier fees if required. Also fit Pajero generation 4
1y
1
Stabiliser bar bushes for Mitsubishi Pajaro generation two, 2.5 and colt bakkie. This is for 4 stabiliser bar bushes. These bushes are made from a 80A shore hardness poly urethane. The colour has no indication other than aesthetic’s.
Please specify vehicle as they differ between the euro and the colt. MR150094. Also fit Hyundai Terracan 54816 H1100
Excludes courier fee.
10mo
2
Frame stop bush for jeep cherokee, also known as a jounce bush this is for the front stop on the jeep cherokee part number 52088684 a c
these bushes tend to fall out when they get old and the rubber perishes i have added a nut and bolt to prevent them from falling out, b u t, if there is no hole for the bolt, you will need to drill one
i have supplied them and received positive feedback
i currently have black in stock, and can make in other colours ( red yellow) the price is for 2 bushes as per the picture
2002 2007 jeep liberty cherokee
1y
2
Stabiliser bar bushes for mitsubishi pajaro generation two, 2 5 and colt bakkie this is for 4 stabiliser bar bushes these bushes are made from a 80 a shore hardness poly urethane the colour has no indication other than aesthetic’s
please specify vehicle as they differ between the euro and the colt MR150094 also fit hyundai terracan 54816 h1100
excludes courier fee
10mo
2
Front differential support bush for Mitsubishi Pajero gen3 ( Gen 4 too). See location of bush. I have rebuilt 2 and fitted one to my vehicle. It definitely reduced the vibration of the vehicle and the in car experience is better/quieter with less plastic rattle.
This is a reasonably easy replacement and can be done without special tools.
R1200 if you want to exchange the unit. I will refund the R500 once I have the old unit in return.
1y
2
Trailing arm bushes for Mitsubishi Pajero 3. These bushes are made using an 80A shore hardness polyurethane. The set consists of 4 matching bushes (2 per side) and 1 steel centre metal bush. The round bush is for the rear of the trailing arm and you will need to reuse the centre metal bush from the old bush.
This set will enable you to do both left and right trailing arm.
The price EXCLUDES a courier fee of R100 within SA.
1y
2
Front Upper strut mounting BUSHES for Mitsubishi Pajero. This is for 4 upper bushes only (2 per side). These bushes made in polyurethane with a shore hardness of 80A. This excludes nuts, washers etc. This excludes courier fees.
1y
2
Polyurethane trailing arm bushes for the Mitsubishi Pajero 2 and 2.5 as per the picture and illustration. Sold as a set of 4 and excludes postage if required. includes the bushes for the links. No 4 and 8 in the picture
Fit 1992 - 2000.
21d
1
Polyurethane Stabiliser bar bushes for Gen3 Mitsubishi Pajero, front and rear. 80A shore hardness. These bushes are easy to fit and no special tools are required and a bit of labour. I have personally fitted these bushes to my Pajero and find them to be hard wearing and I have not yet had any noise.
2 x Front and 2 x Rear R350 or R200 for a set of 2. Excludes postage if required. The left one is for the front (slightly smaller) and the right is for the rear.
I currently have stock available.Now available in yellow.
10mo
1
Polyurethane bushes for Gen2 Mitsubishi Pajero and new shape Colt Bakkie upper control arm bushes and stabilizer bar bushes. 80A shore hardness. Available in black, red and now availble in yellow. Easy to install without any special tools and some medium labour. The price is for four upper control arm bushes and excludes postage if required.
I have stock on hand and can dispatch quickly. I have added a steel washer for durability. It is molded into the bush during production.
10mo