Soldering Ads | Gumtree Classifieds South Africa

Clear All

Results for soldering in "soldering" in South Africa in South Africa

Multi-Jet (Class C) polymer water meter – 40mm

R 3,632.85

Save

Please note that shipping and installation is not included. Firstly the Multi-Jet (Class C) polymer water meter – 40mm. Accurate measurement of the volume of cold potable water consumption. Zone metering and area monitoring. FEATURES Complies with SANS1529 -1: 2019 Class C specifications.Meter for horizontal installation.Pulse prepared.Clear, easily read, dry dial 6-digit counter.Sealed dry dial register.Working temperature between ≤ 50°C.Internal plus removable strainer. (2 strainers).Maximum working pressure 1600 kPa.Glass reinforced polymer body for maximum strength.Meter pressure tested to 4800 kPa.Magnetic drive, lower transmission resistance.A magnetic shield prevents external magnetic interference.Pulse prepared. A reed switch is an optional extra Installation Instructions Step 1: Protecting the Meter Firstly ensure the Multi-Jet (Class C) polymer water meter – 40mm is covered after installation to protect it from direct sunlight. This can be done using a housing or meter box. Step 2: Sizing Afterwards ensure the water meter is properly sized according to the pipe size or flow rate. Step 3: Flushing Pipework Before Installation Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install the meter horizontally with the dial face upright. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, as this can cause damage. Step 6: Fitting Installation Avoid over-tightening fittings or using excessive sealing materials like tape, which can cause leaks. Step 7: Thread Treatment Do not use hemp on the inlet or outlet threads. Instead, use thread tape or PTFE tape, ideally with tail pieces. Step 8: Soldering Precautions Also avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter is used only for cold water applications and not in hot water pipelines. Step 10: Appropriate Usage Use the meter exclusively for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter with care as it is a precision instrument. Do not drop it or damage the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; tailpieces are recommended. Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from debris or sand.Conclusion:At this instant by following these steps, you will ensure optimal meter performance and maintain compliance with warranty guidelines. Evidently the Water Company will repair or replace defective meters at their discretion. By and large proper installation is key to a long-lasting, accurate water meter.

Mbombela / Nelspruit

Domestic plastic water meter, pulse ready – 15mm

R 521.64

Save

Please note that shipping and installation is not included. Firstly the Domestic plastic water meter – pulse ready – 20mm. Measurement of volume of cold potable water consumption. Suitable for both domestic and small business applications. FEATURES Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering. Installation Instructions Thank you for purchasing this high-quality Polymer Piston Domestic Water Meter. The steps below will guide you through the proper installation process for your Polymer Piston Water Meter to ensure top performance and compliance with warranty conditions provided by The Water Company. Step 1: Protecting the Meter Firstly start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box. Step 2: Sizing Secondly make sure the water meter is correctly sized according to the pipe size or the flow rate. Step 3: Flushing Pipework Before installation: Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install piston meters either horizontally or vertically. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, which can lead to failure. Step 6: Fitting Installation Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks. Step 7: Thread Treatment Only use thread tape or PTFE tape, ideally with tailpieces. Step 8: Soldering Precautions Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter installed for cold water is not used in a hot water pipeline. Step 10: Appropriate Usage Use the meter only for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; Use of tailpieces is preferable. Step 13: Additional Protection Install a strainer before the water meter to protect it from sand or foreign debris.

Mbombela / Nelspruit

Save this search and get notified

when new items are posted!

...

"soldering" in South Africa

soldering in South Africa (340 results)

Results for soldering in "soldering" in South Africa in South Africa