Please note that our Terms of Use and Privacy Notice are applicable.
On Promotion in Sports & Leisure
Filter & refine
Clear All
Results for vintage in Used Musical Instruments for sale in Pretoria / Tshwane
4
R 1,499
SavedSave
A high quality pickguard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers. Complete with pickups and electronics installed and connected, all you need to do is disconnect your old pickguard from output jack and connect this pickguard to the output jack with a soldering iron and one wire must be soldered to the tremolo claw (Solderless options available) and screw the pickguard to the body of the guitar (screws can be ordered separately) Please note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards as we make them specially for each order. Pickups: Karman KS35 Alnico Pickups – a classic voiced pickup with a more modern output than your typical classic pickups, bridge pickup is overwound slightly to make it hotter. Comes with staggered pole pieces.Neck 6.5kMiddle 6.5kBridge: 7.2kWiring: ABS plastic wiring, for vintage cloth wiring please email us your custom requestPotentiometers: Full sized brass shaft potentiometers are used, they are great quality with smooth turning, we use a Linear (B250k) for Volume and Audio Taper (A250k) for Tone with 0.047uF High quality Capacitor, neck and middle pickups are connected to the first tone and bridge is connected to the other tone. (other custom wiring options available – email us with your request)Pickguard colour: 3 ply mint green. Knobs, Pickup covers and Switch tip colours: Vintage Cream (other colours are available for custom orders – email us with your custom request)Solderless or Solder-in: This prewired pickguard comes standard as Solder-in and has 3 wires that must be soldered. A solderless pickguard is also available where you only need to connect wires from your output jack and trem claw to a blue screw terminal with a screwdriver. If you want this pickguard solderless please specify in the order notes or via email.Instructions for installation will be included or you can search Valle Sound Prewired Pickguard Installation on YoutubeGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
13d
VERIFIED
12
Contact f/price
SavedSave
Selling old stock of refurbished recording studio / home cinema soundproof windows & acoustic sound absorption panels. These were originally constructed in accordance with professional acoustic standards & typical requirements encountered in vintage customized recording studios and have proven levels of success in such uses.
Windows: designed for building into walls, of sturdy construction, attractive solid wood frames, multiple glass panes and very high level rejection of vibration & audio sound wave transmittance. Various sizes available - prices from R5500 to R15000.
Acoustic Sound absorption Panels: portable & strong, constructed of various HF/MF absorption materials, stained & varnished solid wood frame, attractive material covered face. Can be mounted away from wall for improved bass trap response, allows for many flexible ways to affix or hang onto walls, etc. Sizes (mm): 1200x600, 600x600, various other odd sizes. Prices range from R650 to R950
I have many years of experience in Sound Engineering and as an Acoustic design consultant. Can assist with advice, planning & knowledge of acoustic design principles for various applications, if you can provide a decent floor/wall plan and clear objectives. No installation is offered, but very basic handyman skills should be more than sufficient.
No COD whatsoever!
Mobile: 082 807 4333 WhatsApp / Sms (non-verbal, cannot speak!). Email: friedelknobel@gmail.com
2mo
VERIFIED
4
R 69
SavedSave
High Quality Guitar Tremolo Cavity Cover Backplate for Vintage Strat Style Electric Guitars.This 1ply pickguard is meant to replicate the older vintage style 1.8mm thick tremolo covers that have aged slightly. The colour is a very light cream / off white colour to immitate a white cover that has aged over the years.Size: 144*91.5mmColor: Vintage WhiteMaterial: PVC, 1plyStyle: Strat guitar back cover.* Cut perfectly, with clean surface and smooth edge (sometimes covers may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–screws sold separatelyGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
2mo
VERIFIED
3
R 199
SavedSave
US standard guitar pickguard replacement for Telecaster style guitarsTemplateUS standard styleMaterial: PVC, 3plyColor: Parchment (Vintage white)Thickness: 2.3mmMounting holes: 8 holesPickup rout: Standard tele neck pickup* Cut perfectly, with a clean surface and smooth edge (sometimes pickguards may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–Pickguard screws sold separatelyGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
2mo
VERIFIED
12
Contact f/price
SavedSave
Selling old stock of refurbished recording studio / theatre soundproof windows. These were originally constructed in accordance with professional acoustic standards & typical requirements encountered in vintage customized recording studios and have proven levels of success in such uses.
Windows to designed for building into walls, of sturdy construction, attractive solid wood frames, multiple glass panes and very high level rejection of vibration & audio sound wave transmittance. I have many years of experience in Sound Engineering and as and Acoustic design consultant. Can assist with advice, planning & knowledge of acoustic design principles for various applications. No installation is offered, but very basic handyman skills should be more than sufficient. 1) Attractive design, sturdy construction2 )Double framed with 20mm laminated solid wood panels3) 3 x 5mm thick clear glass panes4) All glass panes encased in rubber edging to prevent vibration transmittance5) Non- parallel glass surfaces for maximum soundwave dispersion6) Outside glass panes angled for downwards reflection of MF/HF 7) All inside smooth surfaces carpeted for maximum soundwave absorption8) Inside trough filled with dehumidifier desiccant crystals to absorb moisture and prevent misting vapour9) Outside completely stained & varnished for moisture protection when building into wall10) Very high level rejection of audio sound wave transmittance Various sizes available - prices from R5500 to R15000.Black Friday 24/11/2023 - 31/11/2023 ( -10%) Voice / Drum booth / Ctrl Room Width x Height x Depth 600mm (W) x 600mm (H) x 400mm (D) - R5500.00 600mm (W) x 690mm (H) x 500mm (D) - R6000.00 640mm (W) x 690mm (H) x 500mm (D) - R6500.00 760mm (W) x 690mm (H) x 500mm (D) - R7500.00 900mm (W) x 620mm (H) x 500mm (D) - R10000.001200mm (W) x 740mm (H) x 500mm (D) - R15000.00 No COD whatsoever!
Mobile: 082 807 4333 WhatsApp / Sms (non-verbal, cannot speak!). Email: friedelknobel@gmail.com
2mo
VERIFIED
3
R 249
SavedSave
Top quality standard guitar 11 hole pickguard replacement for 1 x humbucker, 2 x single coil strat type guitars. Fits Standard Fender USA/MEX strat as well as most other Strat copies.* Color: Vintage White Pearloid* Material: 3ply PVC + Celloid* Thickness: 2.35mm* Pickup rout: Single Coil, Single coil, Humbucker pickup rout* Full size shielding aluminum foil on back (actual foil – not paper)* HSH/SSS/HH pickup rout pickguards available as well as other colors available.* Cut perfectly, with clean surface and smooth edge (sometimes pickgaurds may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–Pickguard screws sold separatelyGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
3mo
VERIFIED
5
R 79
SavedSave
High Quality Guitar Tremolo Cavity Cover Backplate for Vintage Strat Style Electric Guitars with 6 individual cut-outs for each string, we also have the more modern version with one large cut-out to feed the strings through.Size: 144*91.5mmColor: White PearloidMaterial: Celloid, PVC, 3plyStyle: Strat guitar back cover.* Cut perfectly, with clean surface and smooth edge (sometimes covers may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–screws sold separatelyGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
6mo
VERIFIED
2
R 1,999
SavedSave
Custom made 22 Frets Roasted Maple Neck for Telecaster Guitars.What is Roasted Maple? Roasted maple necks undergo a special kiln drying process which involves heating the wood to over 200 degrees in a special kiln, removing the moisture from the wood. This process vulcanizes the wood, making it stronger. The big advantage is that after this process, the wood becomes much less susceptible to moisture and climate changes, resulting in a more stable and predictable piece of wood. This is great for necks, especially, and will minimize the need for adjustments between seasons and different weather conditions. An extra added bonus from this process is that, while stabilizing figured maple, which is typically not so stable, it also greatly enhances the colour and figure in the wood. The finished product usually looks stunning and has improved tone, which is why it usually is the choice of wood for boutique and high end guitars.This neck is perfect as an upgrade as if you are building your own parts caster. No expense has been spared in terms of the materials used in this amazing neck.Specifications:Neck: Roasted MapleFretboard: Roasted MapleTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 42.3mm Bone NutHeadstock: Standard TelecasterRadius: 9.5 Inch RadiusBack profile: C shapePeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth/Thickness (including fretboard and excluding fret): 27.3mmThickness at 1st Fret (Including fretboard and excluding fret): 23.3mmThickness at 12th Fret (Including fretboard and excluding fret): 24.6mmColour: Gloss finish, Roasted maple.Weight: Approx. 700gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel. The tuners that fit into this neck are 10mm tuners, not 8mm vintage style tuners. Please purchase Tuners, String Tree and Neck Plate separately.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
4
R 649
SavedSave
A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 single coil pickups, 1 humbucker and 2 single coils or 2 humbuckers and one single coil. Since the components are customizable you can chose your desired layout and values. The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers (Either flat bottom or with the notch – depending what we have available). Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:Output jack hot gets connected to the white terminalNeck pickup to the blue terminalMiddle pickup to the red terminalBridge pickup to the yellow terminalPlease note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please order via our Valley Sound website in order to select from these customisable options.Volume Potentiometer options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)Most modern guitar manufacturers (or non Fender USA Standard guitars) use 250k Linear pots for volume, Standard / Vintage US Strats typically come with Audio Taper volume pots. Both work but linear has more even controll, Audio Taper has most of the controll happen between 7 – 10.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 1,799
SavedSave
Pickups: Karman Vintage Pro Pickups. Comes with staggered pole pieces.Neck 7.2kMiddle 7.3kBridge: 7.4kWiring: Vintage Cloth WiringPotentiometers: Full sized brass shaft potentiometers are used, either flat top or concave, which ever we have available at the time. We use Audio Taper (A250k) for Volume with Treble Bleed Mod installed and A250K for Tones with 0.047uF High quality Capacitor, neck and middle pickups are connected to the first tone and bridge is connected to the other tone. (other custom wiring options available – email us with your request)dPickguard colour: White (other colours are extra – email us with your custom request)Knobs, Pickup covers and Switch tip colours: White (other colours are available for custom orders – email us with your custom request)Solderless or Solder-in: This prewired pickguard comes standard with Solder-in, all wires you need to solder to your output jack and ground wire for tremolo claw are connected, you must just solder them to the parts. Solderless is an option too and comes with a terminal block on top of the volume potentiometer that you can connect your ground wires in the one terminal and hot from output jack to the other with a small flat screwdriver. If you want this pickguard completely solderless please email us or mention it in th order notes.Instructions for installation will be included.PLEASE NOTE: This pickguard is the exact layout and spec as USA/MEX Strat, it will fit Squier too, though sometimes the screw holes won’t line up 100 percent and you must make new ones. It may fit other guitars with some retrofitting, but we can not guarantee this since there are too many variations of the Strat. Also take note that the switch is larger than the cheaper import switch which may require some extra routing to your body where the switch goes depending on your routing depth (35mm is required) some guitars like Bullet and Affinity Squier have very shallow routing. By purchasing this prewired pickguard we will assume you have removed your current pickguard and checked your routing cavity and we will also assume you are willing to make some modifications if your guitar does not have the same mounting layout as standard USA/MEX Fender.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
3
R 1,799
SavedSave
Pickups: Karman Vintage Pro Pickups. Comes with staggered pole pieces.Neck 7.2kMiddle 7.3kBridge: 7.4kWiring: Vintage Cloth wiringPotentiometers: Full sized brass shaft potentiometers are used, either flat top or concave, which ever we have available at the time. We use Audio Taper (A250k) for Volume with Treble Bleed Mod installed and A250K for Tones with 0.047uF High quality Capacitor, neck and middle pickups are connected to the first tone and bridge is connected to the other tone. (other custom wiring options available – email us with your request)Pickguard colour: Tortoiseshell (other colours are available – email us with your custom request)Knobs, Pickup covers and Switch tip colours: White (other colours are available – email us with your custom request)Solderless or Solder-in: This prewired pickguard comes standard with Solder-in, all wires you need to solder to your output jack and ground wire for tremolo claw are connected, you must just solder them to the parts. Solderless is an option too and comes with a terminal block on top of the volume potentiometer that you can connect your ground wires in the one terminal and hot from output jack to the other with a small flat screwdriver. If you want this pickguard completely solderless please email us or mention it in th order notes.Instructions for installation will be included.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 99
SavedSave
Output jack for guitar prewired with vintage style braided cloth wire. Wires twisted together to ground acts as shielding. Length of wire approximately 15 – 20cm.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
5
R 199
SavedSave
Full size Gibosn SG type guitar pickguard, may not fit Epiphone or other copies without modification so if you are unsure please see measurements, we can not guarantee that it will fit unless your guitar is built to US SG Spec. Vintage white is an off-white colour with a slight yellowish, mint green tint, it looks like white that has naturally aged.MaterialPVCLayers3plyColourVintage White (parchment)Thickness2.3mm* Cut perfectly, with clean surface and smooth edge (sometimes pickgaurds may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–Pickguard screws sold separatelyDid you know at Valley Sound we source the best quality pickguards available in the world? Shop with confidence.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
6
R 399
SavedSave
Great quality 6 in line tuners.Colour: ChromeTuner Button Shape: OvalQuantity: 6 (all Right handed)Headstock Holes: Fits 8mm holesMaterial: Chrome plated steelSet of 6 in-line Kluson style button tuning keys accompanied with colour matched bushings, washers and screws.They feature hole through posts (not split posts)Set Includes:6 x Tuners plus all mounting bushings, washers and screws needed.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
3
R 70
SavedSave
Vintage style push-back cloth wire with outer waxed cotton braid.The inner wire is stranded copper which is tinned. It is also rigid so you can bend it in place and it stays there, which makes for neater wiring.Length: Per meter, select how many meters you want. 1 meter should be enough to do your average guitar.Wire thickness is 22 AWG (1.8mm outer diameter)Available in White (off-white) Yellow and Black.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 349
SavedSave
Top quality pickguard fits Left Hand Fender standard US precision bass in vintage tortoise colour* Material: 3ply PVC* Thickness: 2.35mm* Pickup rout: Precision bass pickups* Cut perfectly, with clean surface and smooth edge (sometimes pickguards may appear rough around the edges in pictures but this is just the protective plastic cover that peels off)–Pickguard screws sold separatelyAt Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 25
SavedSave
Switch tip for 3 / 5 way lever switch on Telecaster Style Guitars that use the asian/metric size switches (not suitable for larger vintage/USA switches)Available in White or BlackPrice is per tip.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
6
R 449
SavedSave
This bridge features 6 individual adjustable saddles, allowing you to set the correct intonation and action on your guitar. This bridge fits a standard Telecaster bridge pickup. String through body design.Complete with fitting screws and adjustment Allen key.Available in Chrome, Black and GoldPlease check the dimensions in the images. Telecasters have 2 common styles of bridges, the vintage “ashtray” style with smaller base plate and 4 mounting screws at the back and then the more modern style base plate with 5 mounting screws (3 at the back and 2 in front) These bridges are not interchangeable without doing some modifications to your guitar.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 1,999
SavedSave
Custom made 22 Frets Roasted Maple Neck for Stratocaster Guitars.What is Roasted Maple? Roasted maple necks undergo a special kiln drying process which involves heating the wood to over 200 degrees in a special kiln, removing the moisture from the wood. This process vulcanizes the wood, making it stronger. The big advantage is that after this process, the wood becomes much less susceptible to moisture and climate changes, resulting in a more stable and predictable piece of wood. This is great for necks, especially, and will minimize the need for adjustments between seasons and different weather conditions. An extra added bonus from this process is that, while stabilizing figured maple, which is typically not so stable, it also greatly enhances the colour and figure in the wood. The finished product usually looks stunning and has improved tone, which is why it usually is the choice of wood for boutique and high end guitars.This neck is perfect as an upgrade as if you are building your own parts caster. No expense has been spared in terms of the materials used in this amazing neck.Specifications:Neck: Roasted MapleFretboard: Roasted MapleTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 43mm Bone NutHeadstock: 60’s StratocasterRadius: 9.5 Inch RadiusBack profile: C shapePeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth/Thickness (including fretboard and excluding fret): 27.3mmThickness at 1st Fret (Including fretboard and excluding fret): 23.3mmThickness at 12th Fret (Including fretboard and excluding fret): 24.6mmColour: Gloss finish, Roasted maple.Weight: Approx. 700gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel. The tuners that fit into this neck are 10mm tuners, not 8mm vintage style tuners. Please purchase Tuners, String Tree and Neck Plate separately.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
7mo
VERIFIED
4
R 649
SavedSave
A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 single coil pickups, 1 humbucker and 2 single coils or 2 humbuckers and one single coil. Since the components are customizable you can chose your desired layout and values. The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers (Either flat bottom or with the notch – depending what we have available). Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:Output jack hot gets connected to the white terminalNeck pickup to the blue terminalMiddle pickup to the red terminalBridge pickup to the yellow terminalPlease note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please order via our Valley Sound website in order to select from these customisable options.Volume Potentiometer options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
7mo
VERIFIED
Save this search and get notified
when new items are posted!
