Please note that our Terms & Conditions and Privacy Notice are applicable.
Pay & Ship
Buy with confidence. Secure payment options & nationwide delivery. Learn more
Filter & refine
Clear All
Suggested
Results for singles in "singles" in Mpumalanga in Mpumalanga
1
R 12,089
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 1.2kW – single
phase with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 1.2kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 8.63
Output Voltage A: 38HP: 1.6
3d
Mbombela / Nelspruit1
R 9,850
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 0.75kW – single
phase with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.75kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 5.13
Output Voltage A: 20HP: 1
3d
Mbombela / Nelspruit1
R 7,880
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel DAB Feka vs submersible pumps 0.55kW – single
phase with micro cast steel liquid vortex impeller, suitable for
lifting sewage and drain water in general containing solid matter with
size up to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.55kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 4.2
Output Voltage A: 20HP: 0.75
3d
Mbombela / Nelspruit1
R 11,779
SavedSave
Please note that shipping and installation is not included.Firstly Stainless steel Feka vs submersible pumps 1kW – single phase
with micro cast steel liquid vortex impeller, suitable for lifting
sewage and drain water in general containing solid matter with size up
to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina.
DAB Feka vs submersible pumps 1kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Power Cable: 10 meter H07RN-F, with plug for the single phase version.
Input Voltage A: 6.63
Output Voltage A: 31HP: 1.36
3d
Mbombela / Nelspruit1
R 9,740.99
SavedSave
Please note that shipping and installation is not included.Firstly Feka vs submersible pumps 0.75kW – single phase with micro
cast steel liquid vortex impeller, suitable for lifting sewage and drain
water in general containing solid matter with size up to 50 mm.
Construction Features Of The Pump
AISI 304 stainless steel pump body, seal cover, motor cover, and cap
with handle insulating rubber coated. Micro cast steel impeller.
Insulating rubber covered handle. AISI 316 stainless steel motor shaft.
Double mechanical seal with interposed oil chamber (non-toxic oil) in
carbon-alumina on the motor side, and silicon carbide/silicon carbide on
the pump side. Mechanical seal: Silicon Carbide
Construction Features Of The Motor
Dry, asynchronous and waterproof motor, cooled by the pumped liquid.
Rotor running on permanently lubricated ball bearings, selected to
ensure low noise and durability. Over current protection as standard for
the single-phase version, optional for the three-phase version.
Permanently connected capacitor in the single-phase version.
Continuous duty with liquid temperature 35 °C and completely
submerged pump. The single-phase version can be supplied with float for
automatic operation. Mechanical seal: Carbon/Alumina
DAB Feka vs submersible pumps 0.75kW – single phase Number of poles: 2 Max starts/hour: 20
Operating range: From 0 to 32 m3/h with head up to 14 meters.
Pumped liquid: Sewage water and used water in general, non aggressive.
Free passage: 50 mm.
Liquid temperature range: From 0 °C to +35 °C for domestic use (EN 60335-2-41). From 0 °C to +50 °C for other uses.
Maximum ambient temperature for operation with motor above water: +40 °C
Maximum immersion depth: 7 meters.
Motor protection class: IP 68
Insulation class: F
Power Inputs: 1 x 220 V -240 V – 50Hz single phase
Installation: Fixed or portable, vertical position
Input Voltage A: 5.13
Output Voltage A: 20HP: 1
3d
Mbombela / Nelspruit1
R 17,576
SavedSave
Please note that shipping and installation is not included.DAB Centrifugal single impeller K pump 2.2kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 2.2kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 1.1/2″
Outlet: 1″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 11,636
SavedSave
Please note that shipping and installation is not included.DAB Centrifugal single impeller K pump 1.8kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 1.8kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 2″
Outlet: 2″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 3,698
SavedSave
Please note that shipping and installation is not included.DAB centrifugal single impeller K pump 0.37kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB centrifugal single impeller K pump 0.37kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 1″
Outlet: 1″
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 19,395
SavedSave
Please note that shipping and installation is not included. DAB Centrifugal single impeller K pump 2.2kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 2.2kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 2 1/2″
Outlet: 2″
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 8,485
SavedSave
Please note that shipping and installation is not included.DAB Centrifugal single impeller K pump 1.1kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 1.1kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 1.1/2″
Outlet: 1″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 5,091
SavedSave
Please note that shipping and installation is not included.DAB Centrifugal single impeller K pump 0.75kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 0.75kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 1.1/2″
Outlet: 1″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 4,122
SavedSave
Please note that shipping and installation is not included.DAB centrifugal single impeller K pump 0.75kW – single phase
centrifugal pump is suitable for domestic, civil, industrial and
agricultural systems, and for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB centrifugal single impeller K pump 0.75kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 1″
Outlet: 1″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 9,699
SavedSave
Please note that shipping and installation is not included.DAB Centrifugal single impeller K pump 1.8kW – single phase is
suitable for domestic, civil, industrial and agricultural systems, and
for decanting, mixing and irrigation uses.
CONSTRUCTION FEATURES OF THE PUMP
Pump body and motor support in cast iron.
Techno polymer or cast iron impeller, as per the TECHNICAL DATA table.
Carbon/ceramic mechanical seal.
CONSTRUCTION FEATURES OF THE MOTOR
Closed asynchronous type, external ventilation cooling.
Rotor running on ball bearings, oversized to ensure low noise and durability.
Standard built-in thermo-amperometric protection. Capacitor permanently fitted on single phase versions.
For the protection of the three-phase motor, we recommend the use of
remote overload cut-outs, in compliance with current local regulations.
DAB Centrifugal single impeller K pump 1.8kW – single phase
Maximum operating pressure: 6 bar (600 kPa)
Maximum ambient temperature: +40°C
Liquid temperature range: From -10 °C to +50 °C.
Installation: Horizontal or vertical position, provided that the motor is always above the pump.
Pumped liquid: clean, free of solids and abrasives, non-viscous,
non-aggressive, non-crystallized and chemically neutral, with properties
similar to water.
Standard voltage:
Single-phase 220-240 V
CONSTRUCTION FEATURES OF THE PUMP
Inlet: 2″
Outlet: 1 1/4″Pump body and motor support in cast iron.
Techno polymer or cast iron impeller.
Carbon/ceramic mechanical seal.
11d
Mbombela / Nelspruit1
R 34,823
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 1.5kW single phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 1.5kW single phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motorSingle-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C.
Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
3d
Mbombela / Nelspruit1
R 28,495
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 0.7kW single phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 0.7kW single phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 \ ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motorSingle-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C. Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
3d
Mbombela / Nelspruit1
R 31,659.01
SavedSave
Please note that shipping and installation is not included.DAB grinder FX submersible pump 1.1kW single phase with a shredder
designed for lifting and transferring wastewater in civil and commercial
environments. Grinder FX is certified EN 12050-1.
The presence of the shredder makes the pump suitable for systems with
small diameter pipes or those requiring high pressures. Shredder in
AISI 630 stainless steel. Ideal pump for replacements thanks to its
reduced dimensions and to both flanged and threaded delivery ports.
Technical Data of the DAB grinder FX submersible pump 1.1kW single phase
Flow rate minimum and maximum: 23,8 m3/hHead up to: 33 mImmersion dept (maximum): 20 mType of pumped liquid: loaded waters with filamentary bodies, paper or textile material in the presence of domestic or civil wasteSupported liquid temperature (maximum and minimum): + 50°C (+ 60°C for short period of time)Flanged and threaded: from 1″½, DN32, DN40Impeller type: GrinderStart time (maximum) per hour: 20/hClass of protection: IP 68Motor insulation class: FSingle phase power input: 1x 220-240V 50HzThree phase power input: 3x 400V 50Hz / 3x 230V 50Hz on requestMaximum dry run time: 10 minPower cable (m) and plug: 10 mPossible type of installation: mobile on the ground or fixed on a coupling deviceCertification: EN 12050 ATEXSpecial versions on request: different cable lengths, different voltages and frequencies
Construction features of the pump
Pump body and impeller in cast iron, shredder in AISI 630. Motor
shaft in AISI 304 stainless steel. Double mechanical seal in
SiC-SiC/SiC-C in oil chamber not in contact with the pumped liquid,
independent of the direction of rotation. Delivery port both flanged and
threaded.
Construction features of the motor
Single-phase asynchronous motor (MA / MNA versions) and three-phase
version motor (TNA versions). The rotor is mounted on lubricated
bearings. Continuous operation in S1 with the motor completely immersed.
Dry running for a maximum time of 10 minutes. Over-temperature sensors
in the motor windings with intervention threshold at +130°C.
Quick-bonded resin-bonded cable gland, 07RN8-F power cable. Single-phase
versions with starter and capacitor in a separate panel, MA versions
with float for automatic operation. In the three-phase motors the
over-temperature sensor connection is responsibility of the user.
3d
Mbombela / Nelspruit1
R 5,089
SavedSave
Please note that shipping and installation is not included.DAB jet self-priming composite pump 0.75kW – single phase Technical Data:
Operating range: from 0.6 to 5.4 m3/h with head up to 54 meters.Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral.Liquid temperature range: from 0°C to +35°C for domestic use (EN 60335-2-41).Maximum ambient temperature: +40°CMaximum operating pressure: 6 bar (600 kPa)Maximum suction depth: 8 meters.Installation: fixed in a horizontal position.Special executions on request: alternative voltages and/or frequencies.Motor protection rating: IP 44Terminal block protection rating: IP 55Insulation class: FStandard input voltage: single phase 220/240 V
Constructional features of the DAB jet self-priming composite pump 0.75kW – single phase:
Pump body in technocpolymer and motor support in die cast aluminium.Impeller, diffuser, venturi tube and sand guard in technopolymerStainless steel wear ring.Carbon/ceramic mechanical seal.
Applications:
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles.Suitable for pumping water with low levels of sandy impurities.Especially used in domestic water supply installations. Suitable for
small farms and gardening, small scale industrial services and where
self priming is necessary.
Constructional features of the motor:Finally the asynchronous type, closed, with external air cooling.
Rotor mounted on oversized greased-for-life ball bearings, to guarantee
low noise and long life. Incorporated thermo-amperometric protection and
permanently inserted capacitor in the single phase version. It is
recommended to use overload protection for three phase motor protection,
in compliance with current legislation. Manufactured pursuant to CEI
2-3 and CEI 61-69 (EN 60335-2-41)
4d
Mbombela / Nelspruit1
Contact f/price
SavedSave
Please note that shipping and installation is not included.DAB jet self-priming composite pump 1kW – single phase Technical Data:
Operating range: from 0.6 to 5.4 m3/h with head up to 54 meters.Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral.Liquid temperature range: from 0°C to +35°C for domestic use (EN 60335-2-41).Maximum ambient temperature: +40°CMaximum operating pressure: 6 bar (600 kPa)Maximum suction depth: 8 meters.Installation: fixed in a horizontal position.Special executions on request: alternative voltages and/or frequencies.Motor protection rating: IP 44Terminal block protection rating: IP 55Insulation class: FStandard input voltage: single phase 220/240 V
Constructional features of the DAB jet self-priming composite pump 1kW – single phase :
Pump body in technocpolymer and motor support in die cast aluminium.Impeller, diffuser, venturi tube and sand guard in technopolymerStainless steel wear ring.Carbon/ceramic mechanical seal.
Applications:
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles.Suitable for pumping water with low levels of sandy impurities.Especially used in domestic water supply installations.Suitable for small farms and gardening, small scale industrial services and where self priming is necessary.
Constructional features of the motor:Finally the asynchronous type, closed, with external air cooling.
Rotor mounted on oversized greased-for-life ball bearings, to guarantee
low noise and long life. Incorporated thermo-amperometric protection and
permanently inserted capacitor in the single phase version. It is
recommended to use overload protection for three phase motor protection,
in compliance with current legislation. Manufactured pursuant to CEI
2-3 and CEI 61-69 (EN 60335-2-41)
4d
Mbombela / Nelspruit1
R 4,456
SavedSave
Please note that shipping and installation is not included.DAB jet self-priming composite pump 0.44kW – single phase Technical Data:
Operating range: from 0.6 to 5.4 m3/h with head up to 54 meters.Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral.Liquid temperature range: from 0°C to +35°C for domestic use (EN 60335-2-41).Maximum ambient temperature: +40°CMaximum operating pressure: 6 bar (600 kPa)Maximum suction depth: 8 meters.Installation: fixed in a horizontal position.Special executions on request: alternative voltages and/or frequencies.Motor protection rating: IP 44Terminal block protection rating: IP 55Insulation class: FStandard input voltage: single phase 220/240 V
Constructional features of the DAB jet self-priming composite pump 0.44kW – single phase:
Pump body in technocpolymer and motor support in die cast aluminium.Impeller, diffuser, venturi tube and sand guard in technopolymerStainless steel wear ring.Carbon/ceramic mechanical seal.
Applications:
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles.Suitable for pumping water with low levels of sandy impurities.Especially used in domestic water supply installations. Suitable for
small farms and gardening, small scale industrial services and where
self priming is necessary.
Constructional features of the motor:Finally the asynchronous type, closed, with external air cooling.
Rotor mounted on oversized greased-for-life ball bearings, to guarantee
low noise and long life. Incorporated thermo-amperometric protection and
permanently inserted capacitor in the single phase version. It is
recommended to use overload protection for three phase motor protection,
in compliance with current legislation. Manufactured pursuant to CEI
2-3 and CEI 61-69 (EN 60335-2-41)
4d
Mbombela / Nelspruit1
R 3,128
SavedSave
Please note that shipping and installation is not included.DAB jet self-priming composite pump 0.75kW – single phase Technical Data:
Operating range: from 0.6 to 5.4 m3/h with head up to 54 meters.Liquid quality requirements: clean, free from solid or abrasive contaminants, non-viscous, non-aggressive, uncrystallised and chemically neutral.Liquid temperature range: from 0°C to +35°C for domestic use (EN 60335-2-41).Maximum ambient temperature: +40°CMaximum operating pressure: 6 bar (600 kPa)Maximum suction depth: 8 meters.Installation: fixed in a horizontal position.Special executions on request: alternative voltages and/or frequencies.Motor protection rating: IP 44Terminal block protection rating: IP 55Insulation class: FStandard input voltage: single phase 220/240 V
Constructional features of the DAB jet self-priming composite pump 0.75kW – single phase:
Pump body in technocpolymer and motor support in die cast aluminium.Impeller, diffuser, venturi tube and sand guard in technopolymerStainless steel wear ring.Carbon/ceramic mechanical seal.Inlet: 1″Outlet: 1″
Applications:
Self priming centrifugal pump with excellent suction capacity even in the presence of air bubbles.Suitable for pumping water with low levels of sandy impurities.Especially used in domestic water supply installations. Suitable for
small farms and gardening, small scale industrial services and where
self priming is necessary.
Constructional features of the motor:Finally the asynchronous type, closed, with external air cooling.
Rotor mounted on oversized greased-for-life ball bearings, to guarantee
low noise and long life. Incorporated thermo-amperometric protection and
permanently inserted capacitor in the single phase version. It is
recommended to use overload protection for three phase motor protection,
in compliance with current legislation. Manufactured pursuant to CEI
2-3 and CEI 61-69 (EN 60335-2-41)
4d
Mbombela / NelspruitSave this search and get notified
when new items are posted!
