Road house in Mpumalanga | Gumtree Classifieds in Mpumalanga

Clear All

Suggested

Results for road house in "road house" in Mpumalanga in Mpumalanga

6000LPH RO system – 3 x 8080 membrane – 3 phase pump

R 400,984.67

Save

Please note that shipping and installation is not included.When you consider purchasing this 6000LPH RO system – 3 x 8080 membrane – 3 phase pump , you need to know the following information as it is very important. This system requires a pretreatment setup for it to perform to its maximum capacity. Firstly a sales agent must recommend a pretreatment setup based on a water analysis report from the lab for it to be guaranteed to work. As shown above for your 6000LPH RO system – 3 x 8080 membrane – 3 phase pump. A water analysis report is very important as it determines the pretreatment setup needed to be installed before the reverse osmosis system. As you can see on the sketch above, the pretreatment consists of a Sand/Glass Filter, Carbon Filter, and Antiscalant Dosing system. Pretreatment setups can consist of even more items installed before the 6000LPH RO System. The water analysis report lists items that may be needed. Chlorine Dosing SystemUltrafiltration SystemDmi-65 Iron Removal Media Filter SystemOzone GeneratorFlocculant SystemAll in all we have our own qualified technicians train by the manufacturers of the equipment to do the installation running of the setup. Training can also be offered to the guys you want to be the ones installing your setup instead of our technicians. TWC’s 6000 l/ph Reverse Osmosis System is part of a family of reverse osmosis units specifically designed for operation with fresh and brackish feed waters having TDS values below 1,500ppm. As a result customers can access these Models with permeate output of 2000 liters/hr as shown in the specifications. Benefits Specialized Micro-Computer ControllerFully Equipped and CustomizableSuper-Quiet Horizontal 3 phase PumpLow Energy ConsumptionHigh Flow Low-Energy MembraneLow Maintenance The reverse osmosis systems have been widely used for commercial purposes such as treatment of wastewater, desalination, minerals reclamation, and purification of water. If you have been searching for the best and most efficient Industrial RO system, then you have landed at the right place. At TWC, we provide the best quality RO water units that can meet your needs, expectations, and budget. As a matter of fact we provide the highest standard and compact commercial reverse osmosis system at an affordable pricing range. All our RO systems are highly durable and we guarantee that they can be last for many years with proper care and maintenance. Standard Features RO micro-computer controller with permeate TDS read out300PSI membrane housingShimge three phase pumpRotameter for permeate and concentrate streamPressure gauges for pre filter feedRO feed High-pressure switchElectro-plated SS304 skid frame

Mbombela / Nelspruit

3000LPH RO system – 6 x 4080 membrane – 3 phase pump

R 176,354.06

Save

Please note that shipping and installation is not included.When you consider purchasing this 3000LPH RO system – 6 x 4080 membrane – 3 phase pump , you need to know the following information as it is very important. This system requires a pretreatment setup for it to perform to its maximum capacity. Firstly a sales agent must recommend a pretreatment setup based on a water analysis report from the lab for it to be guaranteed to work. As shown above for your 3000LPH RO system – 6 x 4080 membrane – 3 phase pump. A water analysis report is very important as it determines the pretreatment setup needed to be installed before the reverse osmosis system. As you can see on the sketch above, the pretreatment consists of a Sand/Glass Filter, Carbon Filter, and Antiscalant Dosing system. Pretreatment setups can consist of even more items installed before the 3000LPH RO System. The water analysis report lists items that may be needed. Chlorine Dosing SystemUltrafiltration SystemDmi-65 Iron Removal Media Filter SystemOzone GeneratorFlocculant SystemAll in all we have our own qualified technicians train by the manufacturers of the equipment to do the installation running of the setup. Training can also be offered to the guys you want to be the ones installing your setup instead of our technicians. TWC’s 3000 l/ph Reverse Osmosis System is part of a family of reverse osmosis units specifically designed for operation with fresh and brackish feed waters having TDS values below 1,500ppm. As a result customers can access these Models with permeate output of 2000 liters/hr as shown in the specifications. Benefits Specialized Micro-Computer ControllerFully Equipped and CustomizableSuper-Quiet Horizontal 3 phase PumpLow Energy ConsumptionHigh Flow Low-Energy MembraneLow Maintenance The reverse osmosis systems have been widely used for commercial purposes such as treatment of wastewater, desalination, minerals reclamation, and purification of water. If you have been searching for the best and most efficient Industrial RO system, then you have landed at the right place. At TWC, we provide the best quality RO water units that can meet your needs, expectations, and budget. As a matter of fact we provide the highest standard and compact commercial reverse osmosis system at an affordable pricing range. All our RO systems are highly durable and we guarantee that they can be last for many years with proper care and maintenance. Standard Features RO micro-computer controller with permeate TDS read out300PSI membrane housingShimge three phase pumpRotameter for permeate and concentrate streamPressure gauges for pre filter feedRO feed High-pressure switchElectro-plated SS304 skid frame

Mbombela / Nelspruit

Save

Responsibilities:Be able to start up boiler fire properly.Monitor water holding JOJO tanks hourly and keep them full of water all the time.Monitor low level water alarm on your hotwell tank.Complete daily boiler maintenance checklist and ensure supervisor signed it after completion.Adjust coal bed as and when required.Close valves and stop supply of steam to production when boiler is not running for minimum 30min due to power outage or breakdown and maintain steam.Change the use of coal screw conveyor weekly with the standby screw conveyor.Keep coal water bath clean and at right level all the time.Keep boiler drains clean all the time.Change the use of boiler water pump weekly with the standby pump.Ensure safety by monitoring safety equipment, identifying potential issues and taking appropriate steps to suspend the operation with consultation with your shift supervisor/maintenance team.Maintain steam pressure for production operation as per steam demand for processing.Continuously communicate with the production operator on steam demand hourly.Monitor and control boiler performance and settings, by reading gauges, meters and charts to track boiler operation.Monitor boiler water and chemicals and coal levels hourly.Maintain the housekeeping of boiler room/area all the time.Monitor your stocker movement every hour to ensure its still aligned on its path.Receiving the delivery of coal and inspect it if complies with grade A peas size without too much duff/loose powder, do this before tipping of coal.Inform your shift supervisor if coat delivered is out of spec.Keep your coal bund pit full all the time.Report low coal level to your shift supervisor for ordering.Ensure you have enough coal daily to last at least 2 days.Grease boiler components that require greasing, if not sure ask maintenance team to show you the greasing points.Updating log sheet/book hourly.Do Soot blowing.Blow down the boilers as instructed by the guideline to remove impurities.Monitoring water level and temperature in the hotwell tank hourly.Continuously check blowdown valve to avoid blockages. Ensuring Water Treatment and Sampling to prevent boiler damages.Trimming of coal and ash removal from grit arrestor.Remove ash trolley as and when required.Cleaning the brine tank and water filter.Cleaning grit collectorEnsure plant equipment hygiene is of top quality.Ensure you apply AEL licence requirements under boiler section.Ensure you give a written handover to the next shift.Ensure you follow the boiler operating procedure by conducting blowdowns, doing TDS etc and record during yourEnsure boiler softener system is working correctl https://www.jobplacements.com/Jobs/B/Boiler-Operator-1204588-Job-Search-07-19-2025-02-00-15-AM.asp?sid=gumtree

7mo

Job Placements

Standerton

R 2,501.25

Save

Please note that shipping and installation is not included.Domestic RO : 75GPD PureWater with Pump Specifications: An Under the Counter RO System is known as the Domestic RO System. This is the Five-Stage Reverse Osmosis System(RO System). This model available in the capacity of 10 – 12 LPH (Liter Per Hour) and 20 LPH for domestic use only. This is the conventional system. It is operated with manual flushing. This is the conventional system. Manual flushing is used to operate it. Reckoned among the eminent manufacturers and suppliers, we offer a reliable range of Domestic RO System (Reverse Osmosis System). While manufacturing these plants our professionals make sure that the raw materials used are procured from the trusted vendor of the industry. All these products are manufactured in compliance with set industry’s norms and standards. We have a wide range of Domestic RO System in our Branded “AquaCare”. We are manufacturing for the last 5 years and supplying high-quality products by our large experience in the Domestic RO System. 5 Stage Filtration75 Gallons Per Day / 190 Liters Per DayLong Reach Chrome Faucet3.2 Gallons / 12 Liters Storage TankAll hardware includedStage 1: 5 microns sediment pre-filterStage 2: Activated Carbon pre-filterStage 3: Carbon block pre-filterStage 4: 75 GPD Reverse Osmosis MembraneStage 5: Inline GAC filterFully Assembled A BRIEF INTRODUCTION TO REVERSE OSMOSIS Reverse Osmosis is a very fine filtration process, which occurs at a molecular level. This process, which allows only a given size of the molecule to pass and rejects the rest. In effect, the pores or holes in the membrane are so small that most of the harmful minerals and chemicals cannot pass. While water molecules pass through. The wastewater pipe drains off water with high mineral concentration, leaving the pure water for the storage tank for drinking.. The System removes up to 95% of harmful minerals and chemicals, the system also removes suspended impurities such as dirt, sand, and rust, it improves the odor and taste of your municipal water and leaves good, clean, and healthy water for your consumption.The optimum pressure for a 2-4-gallon reverse osmosis tank is 6-8 PSI. When the tank is full, the water pressure should read 2 Bar. This may be slightly higher if your tank capacity is larger than average (such as for a whole home RO unit).

Mbombela / Nelspruit

Domestic plastic water meter, pulse ready – 20mm

R 605.48

Save

Please note that shipping and installation is not included. Firstly the Domestic plastic water meter – pulse ready – 20mm. Measurement of volume of cold potable water consumption. Also suitable for both domestic and small business applications. FEATURES Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering. Installation Instructions Thank you for purchasing this high-quality Domestic plastic water meter – pulse ready – 20mm. As a matter of fact the steps below will guide you through the proper installation process for your Polymer Piston Water Meter to ensure top performance and compliance with warranty conditions provided by The Water Company. Step 1: Protecting the Meter Start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box. Step 2: Sizing Make sure the water meter is correctly sized according to the pipe size or the flow rate. Step 3: Flushing Pipework Before installation: Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install piston meters either horizontally or vertically. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, which can lead to failure. Step 6: Fitting Installation Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks. Step 7: Thread Treatment Only use thread tape or PTFE tape, ideally with tailpieces. Step 8: Soldering Precautions Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter installed for cold water is not used in a hot water pipeline. Step 10: Appropriate Usage Use the meter only for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; Use of tailpieces is preferable. Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from sand or foreign debris.

19d

Mbombela / Nelspruit

Domestic plastic water meter, pulse ready – 15mm

R 521.64

Save

Please note that shipping and installation is not included. Firstly the Domestic plastic water meter – pulse ready – 20mm. Measurement of volume of cold potable water consumption. Suitable for both domestic and small business applications. FEATURES Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering. Installation Instructions Thank you for purchasing this high-quality Polymer Piston Domestic Water Meter. The steps below will guide you through the proper installation process for your Polymer Piston Water Meter to ensure top performance and compliance with warranty conditions provided by The Water Company. Step 1: Protecting the Meter Firstly start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box. Step 2: Sizing Secondly make sure the water meter is correctly sized according to the pipe size or the flow rate. Step 3: Flushing Pipework Before installation: Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install piston meters either horizontally or vertically. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, which can lead to failure. Step 6: Fitting Installation Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks. Step 7: Thread Treatment Only use thread tape or PTFE tape, ideally with tailpieces. Step 8: Soldering Precautions Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter installed for cold water is not used in a hot water pipeline. Step 10: Appropriate Usage Use the meter only for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; Use of tailpieces is preferable. Step 13: Additional Protection Install a strainer before the water meter to protect it from sand or foreign debris.

19d

Mbombela / Nelspruit

Multi-Jet (Class C) polymer water meter – 40mm

R 3,632.85

Save

Please note that shipping and installation is not included. Firstly the Multi-Jet (Class C) polymer water meter – 40mm. Accurate measurement of the volume of cold potable water consumption. Zone metering and area monitoring. FEATURES Complies with SANS1529 -1: 2019 Class C specifications.Meter for horizontal installation.Pulse prepared.Clear, easily read, dry dial 6-digit counter.Sealed dry dial register.Working temperature between ≤ 50°C.Internal plus removable strainer. (2 strainers).Maximum working pressure 1600 kPa.Glass reinforced polymer body for maximum strength.Meter pressure tested to 4800 kPa.Magnetic drive, lower transmission resistance.A magnetic shield prevents external magnetic interference.Pulse prepared. A reed switch is an optional extra Installation Instructions Step 1: Protecting the Meter Firstly ensure the Multi-Jet (Class C) polymer water meter – 40mm is covered after installation to protect it from direct sunlight. This can be done using a housing or meter box. Step 2: Sizing Afterwards ensure the water meter is properly sized according to the pipe size or flow rate. Step 3: Flushing Pipework Before Installation Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install the meter horizontally with the dial face upright. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, as this can cause damage. Step 6: Fitting Installation Avoid over-tightening fittings or using excessive sealing materials like tape, which can cause leaks. Step 7: Thread Treatment Do not use hemp on the inlet or outlet threads. Instead, use thread tape or PTFE tape, ideally with tail pieces. Step 8: Soldering Precautions Also avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter is used only for cold water applications and not in hot water pipelines. Step 10: Appropriate Usage Use the meter exclusively for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter with care as it is a precision instrument. Do not drop it or damage the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; tailpieces are recommended. Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from debris or sand.Conclusion:At this instant by following these steps, you will ensure optimal meter performance and maintain compliance with warranty guidelines. Evidently the Water Company will repair or replace defective meters at their discretion. By and large proper installation is key to a long-lasting, accurate water meter.

19d

Mbombela / Nelspruit