Cleaning or domestic work in Kriel | Gumtree Classifieds in Kriel

Clear All

Results for cleaning or domestic work in "cleaning or domestic work" in Kriel in Kriel

Ads in other locations

Domestic plastic water meter, pulse ready – 20mm

R 605.48

Save

Please note that shipping and installation is not included. Firstly the Domestic plastic water meter – pulse ready – 20mm. Measurement of volume of cold potable water consumption. Also suitable for both domestic and small business applications. FEATURES Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering. Installation Instructions Thank you for purchasing this high-quality Domestic plastic water meter – pulse ready – 20mm. As a matter of fact the steps below will guide you through the proper installation process for your Polymer Piston Water Meter to ensure top performance and compliance with warranty conditions provided by The Water Company. Step 1: Protecting the Meter Start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box. Step 2: Sizing Make sure the water meter is correctly sized according to the pipe size or the flow rate. Step 3: Flushing Pipework Before installation: Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install piston meters either horizontally or vertically. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, which can lead to failure. Step 6: Fitting Installation Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks. Step 7: Thread Treatment Only use thread tape or PTFE tape, ideally with tailpieces. Step 8: Soldering Precautions Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter installed for cold water is not used in a hot water pipeline. Step 10: Appropriate Usage Use the meter only for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; Use of tailpieces is preferable. Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from sand or foreign debris.

Mbombela / Nelspruit

Domestic plastic water meter, pulse ready – 15mm

R 521.64

Save

Please note that shipping and installation is not included. Firstly the Domestic plastic water meter – pulse ready – 20mm. Measurement of volume of cold potable water consumption. Suitable for both domestic and small business applications. FEATURES Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering. Installation Instructions Thank you for purchasing this high-quality Polymer Piston Domestic Water Meter. The steps below will guide you through the proper installation process for your Polymer Piston Water Meter to ensure top performance and compliance with warranty conditions provided by The Water Company. Step 1: Protecting the Meter Firstly start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box. Step 2: Sizing Secondly make sure the water meter is correctly sized according to the pipe size or the flow rate. Step 3: Flushing Pipework Before installation: Flush all pipework to remove debris or sand, ensuring a clean pipeline. Step 4: Meter Orientation Install piston meters either horizontally or vertically. Step 5: Avoiding Pressure Ensure no pressure is applied to the meter during installation from misaligned pipes or excessive vibration, which can lead to failure. Step 6: Fitting Installation Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks. Step 7: Thread Treatment Only use thread tape or PTFE tape, ideally with tailpieces. Step 8: Soldering Precautions Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat. Step 9: Water Type Ensure the meter installed for cold water is not used in a hot water pipeline. Step 10: Appropriate Usage Use the meter only for clean potable water to avoid damage and inaccuracies. Step 11: Handling Care Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal. Step 12: Thread Fittings Avoid using tapered thread fittings; Use of tailpieces is preferable. Step 13: Additional Protection Install a strainer before the water meter to protect it from sand or foreign debris.

Mbombela / Nelspruit

Domestic brass water meter – CL C pulse ready – 20mm

R 1,218.71

Save

Please note that shipping and installation is not included. The Domestic brass water meter – CL C pulse ready – 20mm FEATURES Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body. Installation Instructions Installation Requirements Firstly this Domestic brass water meter – CL C pulse ready – 20mm is approved by the NRCS. For vertical and horizontal installation and its accuracy is not affected by the angle of installation. This water meter must be installed using the correct water meter tail pieces. As a matter of fact we sell water meters including tail pieces. N.B. Standard female pipe adaptors must not be screwed directly onto the inlet/outlet of the water meter itself under any circumstances. Note: This is a cold-water meter with a maximum working temperature of 50 °C. Should the water temperature at the metering point exceed this, this meter will be damaged irreparably. Do not solder capillary-type fittings while fitted to the meter or use heat while this meter is fitted in the pipeline. Heat travels through the pipe during this process and this will damage the internals of the water meter irreparably. Any position where the meter may be subjected to shock, cavitation, water hammer or surging due to rapid operation of valves etc. must be avoided as damage to the meter will result. Ensure that the pipework at the metering point lines up correctly so that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. A meter will be damaged and could even burst if the water freezes. The meter should also be installed at least one meter away from any freezing point like a standpipe for example where the water can freeze back down the pipeline from that point.

Mbombela / Nelspruit

Domestic brass water meter – CL C pulse ready – 25mm

R 2,926.46

Save

Please note that shipping and installation is not included. Domestic brass water meter – CL C pulse ready – 25mm FEATURES Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body. Installation Instructions Installation Requirements Firstly the Domestic brass water meter – CL C pulse ready – 25mm is approved by the NRCS. For vertical and horizontal installation and its accuracy is not affected by the angle of installation. This water meter must be installed using the correct water meter tail pieces. As a matter of fact we sell water meters including tail pieces. N.B. Standard female pipe adaptors must not be screwed directly onto the inlet/outlet of the water meter itself under any circumstances. Note: This is a cold-water meter with a maximum working temperature of 50 °C. As a result should the water temperature at the metering point exceed this, this meter will be damaged irreparably. Do not solder capillary-type fittings while fitted to the meter or use heat while this meter is fitted in the pipeline. Heat travels through the pipe during this process and this will damage the internals of the water meter irreparably. Any position where the meter may be subjected to shock, cavitation, water hammer or surging due to rapid operation of valves etc. must be avoided as damage to the meter will result. Ensure that the pipework at the metering point lines up correctly so that damage to the meter by installation stresses is prevented. Another key point precautions must be taken to prevent freezing. All things considered a meter will be damaged and could even burst if the water freezes. The meter should also be installed at least one meter away from any freezing point like a standpipe for example where the water can freeze back down the pipeline from that point.

Mbombela / Nelspruit

Domestic brass water meter – CL C pulse ready – 15mm

R 1,102.27

Save

Please note that shipping and installation is not included. The Domestic brass water meter – CL C pulse ready – 15mm FEATURES Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body. Installation Instructions Installation Requirements Firstly the Domestic brass water meter – CL C pulse ready – 15mm is approved by the NRCS. For vertical and horizontal installation and its accuracy is not affected by the angle of installation. This water meter must be installed using the correct water meter tail pieces. As a matter of fact we sell water meters including tail pieces. N.B. Standard female pipe adaptors must not be screwed directly onto the inlet/outlet of the water meter itself under any circumstances. Note: This is a cold-water meter with a maximum working temperature of 50 °C. As a result should the water temperature at the metering point exceed this, this meter will be damaged irreparably. Do not solder capillary-type fittings while fitted to the meter or use heat while this meter is fitted in the pipeline. Heat travels through the pipe during this process and this will damage the internals of the water meter irreparably. Any position where the meter may be subjected to shock, cavitation, water hammer or surging due to rapid operation of valves etc. must be avoided as damage to the meter will result. Ensure that the pipework at the metering point lines up correctly so that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. All things considered a meter will be damaged and could even burst if the water freezes. The meter should also be installed at least one meter away from any freezing point like a standpipe for example where the water can freeze back down the pipeline from that point.

Mbombela / Nelspruit

Save this search and get notified

when new items are posted!

"cleaning or domestic work" in Kriel

cleaning or domestic work in Kriel (4 results)

Results for cleaning or domestic work in "cleaning or domestic work" in Kriel in Kriel