Please note that our Terms & Conditions and Privacy Notice are applicable.
On Promotion in Home & Garden
Pay & Ship
Buy with confidence. Secure payment options & nationwide delivery. Learn more
Filter & refine
Clear All
Suggested
Results for water meters in "water meters" in Home & Garden Supplies in South Africa in South Africa
1
R 1,218.71
SavedSave
Please note that shipping and installation is not included.
The Domestic brass water meter – CL C pulse ready – 20mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly this Domestic brass water meter – CL C pulse ready – 20mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. Should the water temperature at the
metering point exceed this, this meter will be damaged irreparably. Do
not solder capillary-type fittings while fitted to the meter or use heat
while this meter is fitted in the pipeline. Heat travels through the
pipe during this process and this will damage the internals of the water
meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. A
meter will be damaged and could even burst if the water freezes. The
meter should also be installed at least one meter away from any freezing
point like a standpipe for example where the water can freeze back down
the pipeline from that point.
10d
Mbombela / Nelspruit
1
R 1,102.27
SavedSave
Please note that shipping and installation is not included.
The Domestic brass water meter – CL C pulse ready – 15mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly the Domestic brass water meter – CL C pulse ready – 15mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. As a result should the water temperature
at the metering point exceed this, this meter will be damaged
irreparably. Do not solder capillary-type fittings while fitted to the
meter or use heat while this meter is fitted in the pipeline. Heat
travels through the pipe during this process and this will damage the
internals of the water meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.Another key point precautions must be taken to prevent freezing. All
things considered a meter will be damaged and could even burst if the
water freezes. The meter should also be installed at least one meter
away from any freezing point like a standpipe for example where the
water can freeze back down the pipeline from that point.
10d
Mbombela / Nelspruit
1
R 2,926.46
SavedSave
Please note that shipping and installation is not included.
Domestic brass water meter – CL C pulse ready – 25mm
FEATURES
Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Clear easy read, liquid-filled 8-digit counter.Pulse prepared.Working temperature between 2°C and 40°C.Minimum reading 0,00002m3.Internal Non-Return Valve and Strainer.Working pressure 1600 kPa.Grooved piston for improved performance and reliability.Inlet and Outlet threads are compatible with ISO metric sizes.20mm meter has a bowed strainer with an increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leakproof construction.No external calibration facility prevents tampering.DZR body.
Installation Instructions
Installation Requirements
Firstly the Domestic brass water meter – CL C pulse ready – 25mm is
approved by the NRCS. For vertical and horizontal installation and its
accuracy is not affected by the angle of installation.
This water meter must be installed using the correct water meter tail
pieces. As a matter of fact we sell water meters including tail pieces.
N.B. Standard female pipe adaptors must not be screwed
directly onto the inlet/outlet of the water meter itself under any
circumstances.
Note: This is a cold-water meter with a maximum
working temperature of 50 °C. As a result should the water temperature
at the metering point exceed this, this meter will be damaged
irreparably. Do not solder capillary-type fittings while fitted to the
meter or use heat while this meter is fitted in the pipeline. Heat
travels through the pipe during this process and this will damage the
internals of the water meter irreparably.
Any position where the meter may be subjected to shock, cavitation,
water hammer or surging due to rapid operation of valves etc. must be
avoided as damage to the meter will result.
Ensure that the pipework at the metering point lines up correctly so
that damage to the meter by installation stresses is prevented.
Another key point precautions must be taken to prevent freezing. All
things considered a meter will be damaged and could even burst if the
water freezes. The meter should also be installed at least one meter
away from any freezing point like a standpipe for example where the
water can freeze back down the pipeline from that point.
10d
Mbombela / Nelspruit
6
R 499
SavedSave
Water meter in a purpose made polycarbonate enclosure in good condition with all fittings
Sell R500 cash on collection or courier at extra cost
Please speak 067 291 9996 please don't leave me any messages as I can't reply to them thanks
2d
Kenwyn
1
R 605.48
SavedSave
Please note that shipping and installation is not included.
Firstly the Domestic plastic water meter – pulse ready – 20mm.
Measurement of volume of cold potable water consumption. Also suitable
for both domestic and small business applications.
FEATURES
Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering.
Installation Instructions
Thank you for purchasing this high-quality Domestic plastic water meter – pulse ready – 20mm. As a matter of fact the steps below will guide you through the proper
installation process for your Polymer Piston Water Meter to ensure top
performance and compliance with warranty conditions provided by The
Water Company.
Step 1: Protecting the Meter
Start by ensuring all plastic water meters are covered post
installation. This protects the meter from direct sunlight, which can be
done using a housing or meter box.
Step 2: Sizing
Make sure the water meter is correctly sized according to the pipe size or the flow rate.
Step 3: Flushing Pipework
Before installation:
Flush all pipework to remove debris or sand, ensuring a clean pipeline.
Step 4: Meter Orientation
Install piston meters either horizontally or vertically.
Step 5: Avoiding Pressure
Ensure no pressure is applied to the meter during installation from
misaligned pipes or excessive vibration, which can lead to failure.
Step 6: Fitting Installation
Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks.
Step 7: Thread Treatment
Only use thread tape or PTFE tape, ideally with tailpieces.
Step 8: Soldering Precautions
Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat.
Step 9: Water Type
Ensure the meter installed for cold water is not used in a hot water pipeline.
Step 10: Appropriate Usage
Use the meter only for clean potable water to avoid damage and inaccuracies.
Step 11: Handling Care
Handle the meter carefully as it is a precision measuring instrument. Do not drop it or break the meter seal.
Step 12: Thread Fittings
Avoid using tapered thread fittings; Use of tailpieces is preferable.
Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from sand or foreign debris.
10d
Mbombela / Nelspruit
1
R 1,777.30
SavedSave
Please note that shipping and installation is not included.Rotameter 8 – 40 m3h Plastic Tube Type Water.
Firstly ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.
The straight tube style easily the liquid tube with two end threads
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket75mmF in and outlet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 8 – 40 m3h Plastic Tube Type Water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 521.64
SavedSave
Please note that shipping and installation is not included.Rotameter 250 – 2500 32mmF plastic tube type water
ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.
The straight tube style easily the liquid tube with two end threads.
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket32mmF in and outlet
In reality with an easy-to-read cover on the acrylic body. The
Rotameter 250 – 2500 32mmF plastic tube type water are durable, accurate
in their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
So
Rotameter type flow meters are referred to by a number of names
including rotameter, variable area flow meters, and float-type flow
meters. Variable area rotameter technology has been around for more than
100 years. Finally this type of flow meter is among the most commonly
sold and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 3,632.85
SavedSave
Please note that shipping and installation is not included.
Firstly the Multi-Jet (Class C) polymer water meter – 40mm. Accurate
measurement of the volume of cold potable water consumption. Zone
metering and area monitoring.
FEATURES
Complies with SANS1529 -1: 2019 Class C specifications.Meter for horizontal installation.Pulse prepared.Clear, easily read, dry dial 6-digit counter.Sealed dry dial register.Working temperature between ≤ 50°C.Internal plus removable strainer. (2 strainers).Maximum working pressure 1600 kPa.Glass reinforced polymer body for maximum strength.Meter pressure tested to 4800 kPa.Magnetic drive, lower transmission resistance.A magnetic shield prevents external magnetic interference.Pulse prepared. A reed switch is an optional extra
Installation Instructions
Step 1: Protecting the Meter
Firstly ensure the Multi-Jet (Class C) polymer water meter – 40mm is
covered after installation to protect it from direct sunlight. This can
be done using a housing or meter box.
Step 2: Sizing
Afterwards ensure the water meter is properly sized according to the pipe size or flow rate.
Step 3: Flushing Pipework Before Installation
Flush all pipework to remove debris or sand, ensuring a clean pipeline.
Step 4: Meter Orientation
Install the meter horizontally with the dial face upright.
Step 5: Avoiding Pressure
Ensure no pressure is applied to the meter during installation from
misaligned pipes or excessive vibration, as this can cause damage.
Step 6: Fitting Installation
Avoid over-tightening fittings or using excessive sealing materials like tape, which can cause leaks.
Step 7: Thread Treatment
Do not use hemp on the inlet or outlet threads. Instead, use thread tape or PTFE tape, ideally with tail pieces.
Step 8: Soldering Precautions
Also avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat.
Step 9: Water Type
Ensure the meter is used only for cold water applications and not in hot water pipelines.
Step 10: Appropriate Usage
Use the meter exclusively for clean potable water to avoid damage and inaccuracies.
Step 11: Handling Care
Handle the meter with care as it is a precision instrument. Do not drop it or damage the meter seal.
Step 12: Thread Fittings
Avoid using tapered thread fittings; tailpieces are recommended.
Step 13: Additional ProtectionInstall a strainer before the water meter to protect it from debris or sand.Conclusion:At this instant by following these steps, you will ensure optimal
meter performance and maintain compliance with warranty guidelines.
Evidently the Water Company will repair or replace defective meters at
their discretion. By and large proper installation is key to a
long-lasting, accurate water meter.
10d
Mbombela / Nelspruit
1
R 617.27
SavedSave
Please note that shipping and installation is not included.Rotameter 0.4 – 4 /40mmF plastic tube type water.
Firstly ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.The straight tube style easily the liquid tube with two end threads.
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket40mmF in and outlet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 0.4 – 4 40mmF plastic tube type water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 521.64
SavedSave
Please note that shipping and installation is not included.
Firstly the Domestic plastic water meter – pulse ready – 20mm.
Measurement of volume of cold potable water consumption. Suitable for
both domestic and small business applications.
FEATURES
Approved to SANS1529 -1: 2019 Class C specification.(SA1508).Meter accuracy is not affected by the angle of installation.Approved for both horizontal and vertical installation.Pulse prepared.Clear, easily read, liquid LED 8-digit counter.Minimum reading 0,00002 m3.Working temperature between 2°C and 40°C.Internal Non-Return Valve and Strainer.Working pressure: 1600 kPa.Grooved piston for improved performance and reliability.Inlet and outlet threads are compatible with ISO metric sizes.Meter bodies manufactured from specially blended glass-reinforced UV stabilised polymer tested up to 4800 kPa.20mm meter has a bowed strainer with increased mesh area.20mm & 25mm meter has spring loaded non-return valve.Robust leak proof construction.No external calibration facility prevents tampering.
Installation Instructions
Thank you for purchasing this high-quality Polymer Piston Domestic Water Meter. The steps below will guide you through the proper installation
process for your Polymer Piston Water Meter to ensure top performance
and compliance with warranty conditions provided by The Water Company.
Step 1: Protecting the Meter
Firstly start by ensuring all plastic water meters are covered post installation. This protects the meter from direct sunlight, which can be done using a housing or meter box.
Step 2: Sizing
Secondly make sure the water meter is correctly sized according to the pipe size or the flow rate.
Step 3: Flushing Pipework
Before installation:
Flush all pipework to remove debris or sand, ensuring a clean pipeline.
Step 4: Meter Orientation
Install piston meters either horizontally or vertically.
Step 5: Avoiding Pressure
Ensure no pressure is applied to the meter during installation from
misaligned pipes or excessive vibration, which can lead to failure.
Step 6: Fitting Installation
Avoid over-tightening fittings and excessive use of sealing materials like sealing tape, which can cause leaks.
Step 7: Thread Treatment
Only use thread tape or PTFE tape, ideally with tailpieces.
Step 8: Soldering Precautions
Avoid soldering near the meter, especially where brass fittings are involved, to prevent damage from heat.
Step 9: Water Type
Ensure the meter installed for cold water is not used in a hot water pipeline.
Step 10: Appropriate Usage
Use the meter only for clean potable water to avoid damage and inaccuracies.
Step 11: Handling Care
Handle the meter carefully as it is a precision measuring instrument.
Do not drop it or break the meter seal.
Step 12: Thread Fittings
Avoid using tapered thread fittings; Use of tailpieces is preferable.
Step 13: Additional Protection
Install a strainer before the water meter to protect it from sand or foreign debris.
10d
Mbombela / Nelspruit
1
R 1,258.44
SavedSave
Please note that shipping and installation is not included.Firstly the ground level box – 15mm plastic meter – strainer – SABS
20mm valve . Suitable for both domestic and small business applications.
Pre-plumbed meter installation in a surface/ground level meter box.
Meter Box Features:
Base Plate.UV stabilised lockable lid.2 Way SABS approved plastic ball valve.20mm Polymer male inlet/outlet fittings.Additional servicable fine mesh strainer.
Meter Specifications:
15mm Polymer volumetric piston meter.114mm long with sealed wet dial, non-return valve and pulse output.Meter approved by NRCS to Class C specifications.(SANS 1529-1:2019)
It is essential that the Ground level box – 15mm plastic meter –
strainer – SABS 20mm valve installer works cleanly during the
installation process. The pipeline must be flushed thoroughly prior to
the installation of this water meter. The meter assembly fitted inside
this meter box has been fully pressure tested at the factory. Prior to
dispatch and it is leak free at time of supply.
The water meter fitted in this meter box has been fully Tested and
Verified in Precision Meters SANAS Accredited Verification Laboratory by
a registered Verification Officer prior to it being supplied. This
water meter is verified to SANS 1529-1: 2019 Class C specifications and
it is supplied in a fully functional condition.
As noticed water meter is a precision measuring device which has fine
tolerances between its moving parts. It is designed for the measurement
of potable water only. Grit, sand, or other suspended solids passing
through this water meter will cause the piston to jam and cause
irreparable scouring damage to both piston and chamber. Damage of this
type caused during the installation process is not covered under the
Precision Meters warranty.The meter assembly fitted inside this meter box has been fully
pressure tested at the factory prior to dispatch and it is leak free at
time of supply. The soil directly under the meter box must be well
compacted before the installation of the meter box and the meter box
must be placed on a foundation of two bricks or a small concrete slab to
ensure stability.
10d
Mbombela / Nelspruit
1
R 1,777.30
SavedSave
Please note that shipping and installation is not included.Rotameter 12 – 60 m3h Plastic Tube Type Liquid Water
Firstly ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.
The straight tube style easily the liquid tube with two end threads.
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket75mmF in and outlet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 12 – 60 m3h Plastic Tube Type Water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 1,232.06
SavedSave
Please note that shipping and installation is not included.
Rotameter 1 – 10 m3h plastic tube type water
Firstly ABS material, good sealing
This instrument measures the rate of flow of water
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement
The straight tube style easily the liquid tube with two end threads
Used to measure flow rate of fluid, -way pulsation liquid
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket63mmF in and outlet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 1 – 10 m3h plastic tube type water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 617.27
SavedSave
Please note that shipping and installation is not included.Rotameter 0.6 – 6 m3h Plastic Tube Type Water.
Firstly ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.
The straight tube style easily the liquid tube with two end threads.
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket40mmF in and oulet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 0.6 – 6 m3h Plastic Tube Type Water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 521.64
SavedSave
Please note that shipping and installation is not included.Rotameter 160 – 1600 32mmF plastic tube type water
Firstly ABS material, good sealing.
This instrument measures the rate of flow of water.
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement.
The straight tube style easily the liquid tube with two end threads.
Used to measure flow rate of fluid, -way pulsation liquid.
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 160 – 1600 32mmF plastic tube type water are durable, accurate
in their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 1,323.06
SavedSave
Please note that shipping and installation is not included.Rotameter 1.6 – 16 m3h Plastic Tube Type Water
Firstly ABS material, good sealing
This instrument measures the rate of flow of water
Its measurement lines are printed onto the glass exterior, making it easy to read and derive an accurate measurement
The straight tube style easily the liquid tube with two end threads
Used to measure flow rate of fluid, -way pulsation liquid
This plastic Rotameter water flow meter is specifically designed to
provide a high level of accuracy when measuring the amount of water
supplied through the pipeline. Not easy to break, durable.
Max temp: 60 deg CelsiusMax pressure: 6 barBody: AcrylonitrilestyreneFloat/Guide: Plastic / 316L Stainless SteelConnectors: UPVC union adapter socket63mmF in and outlet
In reality with an easy-to-read cover on the acrylic body, the
Rotameter 1.6 – 16 m3h Plastic Tube Type Water is durable, accurate in
their measurement. As well as robust and practically indestructible.
In
summary a rotameter is used to measure the rate of liquid flowing
through a system of pipes at any given time. They provide a constant
flow rate measurement and can also offer optional switching capabilities
to control the flow in a system or process.
Rotameter
type flow meters are referred to by a number of names including
rotameter, variable area flow meters, and float-type flow meters.
Variable area rotameter technology has been around for more than 100
years. Finally this type of flow meter is among the most commonly sold
and installed flow meters in the world.
5d
Mbombela / Nelspruit
1
R 1,009.13
SavedSave
Please note that shipping and installation is not included.Firstly the ground level box – 20mm plastic meter – SABS 20mm valve
male in/out. Suitable for both domestic and small business applications.
Pre-plumbed meter installation in a surface/ground level meter box.
Meter Box Features:
Base Plate.UV stabilised polymer lockable lid.2 Way SABS approved plastic ball valve.20mm Polymer male inlet/outlet fittings.Tamper resistant locking mechanism operated with special key.
Meter Specifications:
20mm Polymer volumetric piston meter.165mm long with sealed wet dial, non-return valve and pulse output.Meter approved by NRCS to Class C specifications.(SANS 1529-1:2019)Working pressure 1600 kPa.
It is essential that the Ground level box – 15mm plastic meter – SABS
20mm valve installer works cleanly during the installation process.
The pipeline must be flushed thoroughly prior to the installation of
this water meter. The meter assembly fitted inside this meter box has
been fully pressure tested at the factory prior to dispatch and it is
leak free at time of supply.
The water meter fitted in this meter box has been fully Tested and
Verified in Precision Meters SANAS Accredited Verification Laboratory by
a registered Verification Officer prior to it being supplied. This
water meter is verified to SANS 1529-1: 2019 Class C specifications and
it is supplied in a fully functional condition.
As noticed water meter is a precision measuring device which has fine
tolerances between its moving parts. It is designed for the measurement
of potable water only. Grit, sand, or other suspended solids passing
through this water meter will cause the piston to jam and cause
irreparable scouring damage to both piston and chamber. Damage of this
type caused during the installation process is not covered under the
Precision Meters warranty.The meter assembly fitted inside this meter box has been fully
pressure tested at the factory prior to dispatch and it is leak free at
time of supply.
10d
Mbombela / Nelspruit
1
R 1,405.01
SavedSave
Please note that shipping and installation is not included.Firstly the ground level box – 15mm brass meter – SABS 20mm valve
male in/out. Suitable for both domestic and small business applications.
Pre-plumbed meter installation in a surface/ground level meter box.
Meter Box Features:
Base Plate.UV stabilised polymer lockable lid.2 Way SABS approved plastic ball valve.20mm Polymer male inlet/outlet fittings.Tamper resistant locking mechanism operated with special key.
Meter Specifications:
15mm brass volumetric piston meter.165mm long with sealed wet dial, non-return valve and pulse output.Meter approved by NRCS to Class C specifications.(SANS 1529-1:2019)Working pressure 1600 kPa.
It is essential that the Ground level box – 15mm brass meter – SABS
20mm valve installer works cleanly during the installation process. The
pipeline must be flushed thoroughly prior to the installation of this
water meter. The meter assembly fitted inside this meter box has been
fully pressure tested at the factory prior to dispatch and it is leak
free at time of supply.
The water meter fitted in this meter box has been fully Tested and
Verified in Precision Meters SANAS Accredited Verification Laboratory by
a registered Verification Officer prior to it being supplied. This
water meter is verified to SANS 1529-1: 2019 Class C specifications and
it is supplied in a fully functional condition.
As noticed water meter is a precision measuring device which has fine
tolerances between its moving parts. It is designed for the measurement
of potable water only. Grit, sand, or other suspended solids passing
through this water meter will cause the piston to jam and cause
irreparable scouring damage to both piston and chamber. Damage of this
type caused during the installation process is not covered under the
Precision Meters warranty.The meter assembly fitted inside this meter box has been fully
pressure tested at the factory prior to dispatch and it is leak free at
time of supply.
10d
Mbombela / Nelspruit
1
R 66,136.50
SavedSave
Please note that shipping and installation is not included.Ultrafiltration system auto – 3200 L/PH
Product Features
Inlet pressure: below 3barBack washing pressure: 2barProduce capacity: 3200L/HOperating type: full manual, automatic
Product Parts
Product water valveBack washing inlet water valveInlet valveRinse drain water valveBack washing drain water valveProduce water flow meterWastewater flow meter
How to run the
Ultrafiltration System – 3200 System ?
Before you start operating the machine, there are 3 connection that should be done :
Connect the raw water, from the blue filter housing, the size is 1’’;Connect product water tank or water use site from the pipe of the produced water flow meter, the size is 1’’;Connect the wastewater pipe from the pipe with a waste water flow meter, for recycle, or drain out;Our Ultrafiltration Systems
company is professionally in producing reverse osmosis (RO) water
machine, pure water treatment plant, purified ro water filter,
industrial water, well water treatment unit, softened water equipment,
underground water treatment equipment, iron manganese removal equipment,
laboratory deionized water equipment, deionized water equipment, direct
drinking water equipment, domestic drinking water equipment's, EDI high
purity water, swimming pool water purifying equipment, river, seawater
desalination equipment, ultrafiltration(UF) equipment, electroplate
water treatment equipment, ion exchange equipment- Mixed bed, water
softener, all kinds of water treatment consumable(need replaced parts)
materials(PP sediment cartridge, RO membranes), accessories, can be
customized various kinds of model as your requirements.
6d
Mbombela / Nelspruit
1
R 900.45
SavedSave
Please note that shipping and installation is not included.Firstly
the ground level box – 15mm plastic meter – SABS 20mm valve male
in/out. Suitable for both domestic and small business applications.
Pre-plumbed meter installation in a surface/ground level meter box.
Meter Box Features:
Base Plate.UV stabilised polymer lockable lid.Way SABS approved plastic ball valve.20mm Polymer male inlet/outlet fittings.Tamper resistant locking mechanism operated with special key.
Meter Specifications:
15mm Polymer volumetric piston meter.114mm long with sealed wet dial, non-return.Valve and pulse output.Meter approved by NRCS to Class C specifications.SANS 1529-1:2019Working pressure 1600 kPa.
It is essential that the Ground level box – 15mm plastic meter – SABS
20mm valve installer works cleanly during the installation process.
The pipeline must be flushed thoroughly prior to the installation of
this water meter. The meter assembly fitted inside this meter box has
been fully pressure tested at the factory prior to dispatch and it is
leak free at time of supply.
The water meter fitted in this meter box has been fully Tested and
Verified in Precision Meters SANAS Accredited Verification Laboratory by
a registered Verification Officer prior to it being supplied. This
water meter is verified to SANS 1529-1: 2019 Class C specifications and
it is supplied in a fully functional condition.
As noticed water meter is a precision measuring device which has fine
tolerances between its moving parts. It is designed for the measurement
of potable water only. Grit, sand, or other suspended solids passing
through this water meter will cause the piston to jam and cause
irreparable scouring damage to both piston and chamber. Damage of this
type caused during the installation process is not covered under the
Precision Meters warranty.
The meter assembly fitted inside this meter box has been fully
pressure tested at the factory prior to dispatch and it is leak free at
time of supply
10d
Mbombela / NelspruitSave this search and get notified
when new items are posted!