Please note that our Terms of Use and Privacy Notice are applicable.
On Promotion in Automotive Vehicles
Filter & refine
Clear All
Results for Car Suspension, Shocks & Steering Parts in Diep River
3
R 700
Mitsubishi Pajero generation 3 and 4 rear differential carrier replacement bushes. These bushes are made from polyurethane and are quite easy to replace. Additional tool required is a 40mm wire brush for use on a drill to clean out the old rubber.
Hardness grade is 2/5 and these bushes can be replaced within removing the differential. I will include instructions with pictures.
16d
3
R 1,000
Trailing arm bushes for Mitsubishi Pajero 3. These bushes are made using an 80A shore hardness polyurethane. The set consists of 4 matching bushes (2 per side) and 1 steel centre metal bush. The round bush is for the rear of the trailing arm and you will need to reuse the centre metal bush from the old bush.
This set will enable you to do both left and right trailing arm.
The price EXCLUDES a courier fee of R100 within SA.
16d
2
R 1,200
Lower control arms for For Mitsubishi Pajaro generation 3. These are used control arms in excellent condition. Price is R1200. Set of bushes for these control arms is R800 and if you want the bushes fitted, the total cost is R2300. Suitable for year models from 2000 to 2005.
24d
1
R 300
Stabiliser bar bushes for Mitsubishi Pajaro generation two, 2.5 and colt bakkie. This is for 4 stabiliser bar bushes. These bushes are made from a 80A shore hardness poly urethane. The colour has no indication other than aesthetic’s.
Please specify vehicle as they differ between the euro and the colt. MR150094. Also fit Hyundai Terracan 54816 H1100
Excludes courier fee.
23d
2
R 700
Polyurethane trailing arm bushes for the Mitsubishi Pajero 2 and 2.5 as per the picture and illustration. Sold as a set of 4 and excludes postage if required. Now includes the bushes for the links. No 4 and 8 in the picture
Fit 1992 - 2000.
2mo
1
R 900
The original specification rubber control arm bushes for Mitsubishi Pajero gen3. These bushes are press fitted. Sold as a set (4) bushes. Price excludes courier fees if required. Also fit Pajero generation 4
2mo
1
R 500
Frame stop bush for Jeep Cherokee, also known as a Jounce bush. This is for the front stop on the Jeep Cherokee. Part number 52088684AC.
These bushes tend to fall out when they get old and the rubber perishes. I have added a nut and bolt to prevent them from falling out, BUT, if there is no hole for the bolt, you will need to drill one.
I have supplied them and received positive feedback.
I currently have black in stock, and can make in other colours. (Red/Yellow). The price is for 2 bushes as per the picture.
2002-2007 Jeep Liberty/Cherokee
7mo
2
R 1,500
Mitsubishi Pajero generation 3/4 rear diff front support arm with new bushes. This arm controls lateral movement of the drivetrain and has an effect on engine and drivetrain sideways movement.
I will include fitting instructions and have done this work on my own vehicle. Allow approximately 1 hour and no special tools are required. I sell the bushes separately and have had positive feedback.
16d
1
R 415
Polyurethane Stabiliser bar bushes for Gen3 Mitsubishi Pajero, front and rear. 80A shore hardness. These bushes are easy to fit and no special tools are required and a bit of labour. I have personally fitted these bushes to my Pajero and find them to be hard wearing and I have not yet had any noise.
2 x Front and 2 x Rear R350 or R200 for a set of 2. Excludes postage if required. The left one is for the front (slightly smaller) and the right is for the rear.
I currently have stock available.Now available in yellow.
8d
1
R 595
Polyurethane bushes for Gen3 Mitsubishi Pajero. 80A shore hardness. Provided them in a deep purple so they look black and now available in yellow. Easy to install without any special tools and some medium labour. The price is for four bushes and excludes postage if required. I have personally installed them on my Pajero. Now supplied with steel spacers to improve durability and longevity.
These spacers are molded into the bushing during manufacture. I have stock on hand and can dispatch quickly.
Also fit Mitsubishi Triton.
2mo
3
R 595
Polyurethane bushes for Gen2 Mitsubishi Pajero and new shape Colt Bakkie upper control arm bushes and stabilizer bar bushes. 80A shore hardness. Available in black, red and now availble in yellow. Easy to install without any special tools and some medium labour. The price is for four upper control arm bushes and excludes postage if required.
I have stock on hand and can dispatch quickly. I have added a steel washer for durability. It is molded into the bush during production.
16d
Save this search and get notified
when new items are posted!