Please note that our Terms of Use and Privacy Notice are applicable.
On Promotion in Sports & Leisure
Some search tips we've found useful:
- Check the spelling of your search terms
- Use fewer or more general search terms
- Try browsing a category related to your search terms
Ads in other locations
4
R 69
SavedSave
These potentiometers are custom made for Valley Sound according to our spec. The shaft is solid brass is thicker than your standard 8mm shaft, the shaft has the USA / CTS thread of 9.5mm, if your mounting hole is 8mm (which is normally the standard size for Asian import guitars) then you will need to widen the hole for this pot to work. The shaft is 18mm long for 500k which is perfect for mounting on wood and 15mm long for 250k which is perfect if you have a guitar that has a pickguard or control plate (like a Stratocaster or Telecaster) If you have a pickguard and want to use 500k pots then you will need to purchase either our 10mm spacer (which is also anti-spin) or a set of our extra nut and washer for CTS/USA spec pot and use one nut and washer behind the pickguard to get the correct height for your knob to fit perfectly on the other side.PRICE IS FOR 1 POT – Please add the desired amount of pots to your cart.Required hole size for mounting: 9.5mm (all the pickguards we sell at Valley Sound are USA spec with 9.5mm mounting holes)Pot diameter: 24mm (full size pot)Shaft length: 18mm (A500K/B500K); 15mm (A250K/B250K)Shaft Threaded diameter: 9.5mmShaft diameter for knob: 6mm (split)Includes 1 x washer and nut, if you want more to kind of create a spacer behind the pickguard please purchase “Nut and washer for USA / CTS Pot” separate (Not necessary for 15mm shaft)250k pots are usually used for volume and tone control on single coil pickups500k pots are usually used for volume and tone control on humbucker type pickupsSplit shafts are suitable for push-on control knobs, solid shafts are suitable for knobs that have a tightening screw.Guitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Knobs.
Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners,
Scratch plates / Pick guards, Pre-wired loaded pickguards, Potentiometers,
Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
1mo
VERIFIED
2
Contact f/price
SavedSave
Looking for an offer for my fender stratocaster
1mo
3
R 1,899
SavedSave
Custom made 22 Frets Roasted Maple Neck for Stratocaster Guitars. Look through the pictures, no 2 necks are the same when it comes to grain of the neck and the fretboard we can not guarantee that it will look exactly the same as one of the pictures as we get new batches in all the time but the specs are all the same.Specifications:Neck: Roasted MapleTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 43mm Bone NutHeadstock: 60’s StratocasterRadius: 9.5 Inch RadiusPeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth: 25.5mmColour: Satin finish, Roasted maple.Weight: Approx. 1000gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
4
R 649
SavedSave
A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 single coil pickups, 1 humbucker and 2 single coils or 2 humbuckers and one single coil. Since the components are customizable you can chose your desired layout and values. The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers (Either flat bottom or with the notch – depending what we have available). Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:Output jack hot gets connected to the white terminalNeck pickup to the blue terminalMiddle pickup to the red terminalBridge pickup to the yellow terminalPlease note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please order via our Valley Sound website in order to select from these customisable options.Volume Potentiometer options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)Most modern guitar manufacturers (or non Fender USA Standard guitars) use 250k Linear pots for volume, Standard / Vintage US Strats typically come with Audio Taper volume pots. Both work but linear has more even controll, Audio Taper has most of the controll happen between 7 – 10.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
5
R 1,899
SavedSave
Custom made 22 Frets Roasted Maple Neck for Stratocaster Guitars. Look through the pictures, no 2 necks are the same when it comes to grain of the neck and the fretboard we can not guarantee that it will look exactly the same as one of the pictures as we get new batches in all the time but the specs are all the same.Specifications:Neck: Roasted MapleFretboard: RosewoodTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 43mm Bone NutHeadstock: 60’s StratocasterRadius: 9.5 Inch RadiusPeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth: 25.5mmColour: Satin finish, Roasted maple.Weight: Approx. 1000gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel.Custom made 22 Frets Roasted Maple Neck for Stratocaster Guitars. Look through the pictures, no 2 necks are the same when it comes to grain of the neck and the fretboard we can not guarantee that it will look exactly the same as one of the pictures as we get new batches in all the time but the specs are all the same.Specifications:Neck: Roasted MapleFretboard: RosewoodTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 43mm Bone NutHeadstock: 60’s StratocasterRadius: 9.5 Inch RadiusPeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth: 25.5mmColour: Satin finish, Roasted maple.Weight: Approx. 1000gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
2
R 1,999
SavedSave
Custom made 22 Frets Roasted Maple Neck for Stratocaster Guitars.What is Roasted Maple? Roasted maple necks undergo a special kiln drying process which involves heating the wood to over 200 degrees in a special kiln, removing the moisture from the wood. This process vulcanizes the wood, making it stronger. The big advantage is that after this process, the wood becomes much less susceptible to moisture and climate changes, resulting in a more stable and predictable piece of wood. This is great for necks, especially, and will minimize the need for adjustments between seasons and different weather conditions. An extra added bonus from this process is that, while stabilizing figured maple, which is typically not so stable, it also greatly enhances the colour and figure in the wood. The finished product usually looks stunning and has improved tone, which is why it usually is the choice of wood for boutique and high end guitars.This neck is perfect as an upgrade as if you are building your own parts caster. No expense has been spared in terms of the materials used in this amazing neck.Specifications:Neck: Roasted MapleFretboard: Roasted MapleTruss Road: 2 way, adjustable from the headstockFrets: 22 medium jumboNut: 43mm Bone NutHeadstock: 60’s StratocasterRadius: 9.5 Inch RadiusBack profile: C shapePeg Holes Diameter: 10 mm / 0.4 inchHeel Width: 55.6mmHeel Depth/Thickness (including fretboard and excluding fret): 27.3mmThickness at 1st Fret (Including fretboard and excluding fret): 23.3mmThickness at 12th Fret (Including fretboard and excluding fret): 24.6mmColour: Gloss finish, Roasted maple.Weight: Approx. 700gPackage Includes:1x Guitar NeckPLEASE NOTE: This is a brand new guitar neck that has never been installed, there are no screw holes at the heel. The tuners that fit into this neck are 10mm tuners, not 8mm vintage style tuners. Please purchase Tuners, String Tree and Neck Plate separately.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
4
R 649
SavedSave
A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 single coil pickups, 1 humbucker and 2 single coils or 2 humbuckers and one single coil. Since the components are customizable you can chose your desired layout and values. The layout is a per Fender USA/MEX Standard strat. This will fit squier or other guitars but we can not guarantee the layout will be the same, the pots and switch need to be fixed to the plate, if you are unsure if this plate will fit onto your pickguard you can purchase one of our pickguards, all the pickguards we sell at Valley Sound for Strat will work.Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometers (Either flat bottom or with the notch – depending what we have available). Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our solderless connector. It is easy to do, the connector is spring activated so you just press on the orange part with a screwdriver, insert the wire and release. All the ground wires go to the bottom terminals and each hot goes to top terminals. They will be colour coded so you know where to put the hot of each component:Output jack hot gets connected to the white terminalNeck pickup to the blue terminalMiddle pickup to the red terminalBridge pickup to the yellow terminalPlease note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. Please order via our Valley Sound website in order to select from these customisable options.Volume Potentiometer options:– Linear (B250k / 500k)– Audio Taper (A250k / 500k)At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
5
R 599
SavedSave
A high quality electronic replacement / upgrade for Stratocaster style guitars with 3 Single Coil Pickups (SSS)Comes standard with a Karman Vintage Style 5 way switch, Full Sized Brass Shaft Potentiometer for Volume and tones. Complete with all electronics soldered with vintage spec cloth wire, neatly wired up and installed on a rigid aluminum grounding plate (helps eliminate electrical noise at the same time) all you need to do is disconnect your pickups and output jack from your old electronic assembly and fit this electronic assembly to your pickguard and reconnect the output jack and pickups to our electronics. We also have the bridge grounding and output jack wire pre-soldered onto the assembly so you can feed the white and black wire through to your output jack (jacks sold separately) and 2nd black wire to your bridge for grounding. All the ground wires from your pickups go to the top of the volume pot, 3 blobs of solder are on top of the pot for quick soldering. The hots go to each position on the switch.Please note – You would need to add an extra 24 – 48 hours to the lead time when ordering our prewired pickguards or electronic assemblies as we make them specially for each order. We can do solderless wiring harnesses and we can make any custom wiring assembly, browse the Valley Sound website for examples of other wiring configurations and mods we have done.SPECS:This standard solder-in wiring harness assembly comes with the following specs and components:– A250k Full Size Volume Potentiometer with brass shaft– Trebble bleed mod to prevent trebble loss when rolling back the volume– A250k Full Size Tone Potentiometers with brass shaft– Tone Pot 1 controlls both Neck and Middle pickups tone– Tone Pot 2 controlls Bridge pickup tone– Tone Capacitor Value: 0.047uF (or 47nf)– Vintage Style 5 way selector switch– Selector Switch tip: Black, Cream or White (White is Standard if you do not inform us of a different colour choice)Potentiometer knobs are not included, please purchase them separately should you require. Potentiometers used will either be concave top or flat top, which ever we have available.At Valley Sound
we specialize in replacement and upgrade parts for Electric, Acoustic and Bass
guitars. Please visit our online store to order! www.valleysound.co.za
6mo
VERIFIED
3
R 89
SavedSave
Guitar neck joint plate with screws (no gasket)The Neck Joint Plate is used for Bolt-On Neck Guitars to secure the neck to the body.Will fit most Stratocaster/Telecasters or similar guitars. Some people prefer the neck plate without the plastic gasket, if you do, please see our listing that includes the gasket.Size: 64 x 51 mmModel Number: NP001Material: SteelStyle: Neck joint plateFit For: Strat/tele and other bolt on electric guitarsOut Size: 64*51mmThickness: 2mmSpare parts: 4pcs Mounting screwsColor: Chrome, Black or GoldGuitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Fingerboard
Nuts, Knobs. Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head
Tuners, Scratch plates / Pick guards, Pre-wired loaded pickguards,
Potentiometers, Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
7mo
VERIFIED
5
R 69
SavedSave
These potentiometers are custom made for Valley Sound according to our spec. The shaft is solid brass is thicker than your standard 8mm shaft, the shaft has the USA / CTS thread of 9.5mm, if your mounting hole is 8mm (which is normally the standard size for Asian import guitars) then you will need to widen the hole for this pot to work. The shaft is 18mm long for 500k which is perfect for mounting on wood and 15mm long for 250k which is perfect if you have a guitar that has a pickguard or control plate (like a Stratocaster or Telecaster) If you have a pickguard and want to use 500k pots then you will need to purchase either our 10mm spacer (which is also anti-spin) or a set of our extra nut and washer for CTS/USA spec pot and use one nut and washer behind the pickguard to get the correct height for your knob to fit perfectly on the other side.PRICE IS FOR 1 POT – Please add the desired amount of pots to your cart.Required hole size for mounting: 9.5mm (all the pickguards we sell at Valley Sound are USA spec with 9.5mm mounting holes)Pot diameter: 24mm (full size pot)Shaft length: 18mm (A500K/B500K); 15mm (A250K/B250K)Shaft Threaded diameter: 9.5mmShaft diameter for knob: 6mm (split)Includes 1 x washer and nut, if you want more to kind of create a spacer behind the pickguard please purchase “Nut and washer for USA / CTS Pot” separate (Not necessary for 15mm shaft)250k pots are usually used for volume and tone control on single coil pickups500k pots are usually used for volume and tone control on humbucker type pickupsSplit shafts are suitable for push-on control knobs, solid shafts are suitable for knobs that have a tightening screw.Guitar parts available from our online store:
www.valleysound.co.za
Pickups & Electrical Components to Amplify Your Guitar,
Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings,
Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Fingerboard
Nuts, Knobs. Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head
Tuners, Scratch plates / Pick guards, Pre-wired loaded pickguards,
Potentiometers, Toggle Switches, Selector Switches, Luthier tools, Etc…
A great selection of direct replacement parts for Gibson or
Fender type electric guitars as well as guitar accessories.
Please order online:
www.valleysound.co.za
7mo
VERIFIED
2
R 499
SavedSave
Valley Sound online store delivers all over South Africa
Here is what we stock, visit our website for full list of what is currently in stock and prices. All goods are in South Africa and get dispatched super quick.
Pickups & Electrical Components to Amplify Your Guitar, Control Plates, Jack Plates, Neck Plates, Pickup Covers, Pickup Mounting Rings, Screws, Springs, Straps, Strap Buttons, Strap-locks, String Trees, Thumb Rests, Fingerboard Nuts, Knobs. Acoustic, Electric, Tremolo Bridge & Tailpiece, Machine Head Tuners, Pre-wired loaded pickguards, fret wire, pedals, Etc…
tags: Fender, Squire, Squier Classic Vibe, Gibson, Les Paul, Epiphone, Cort, Stratocaster, Telecaster, ibanez, Marshall, Yamaha, Taylor, Martin, Gretsch, ESP, Rickenbacker, Charvel, PRS, ES-335, SG, Jazzmaster, Boss, Orange, Vox, Roland, Peavey.
www.valleysound.co.za
2y
VERIFIED
9
R 249
SavedSave
Top quality standard guitar 11 hole pickguard replacement for 3 single coil strat type guitars. Fits USA/Mex Standard Stratocasters (except for year '64 strat where 1 screw hole is in a different position) but also fits most other strat copies like squier, etc. Sometimes you may need to file the pickguard with a nail file around the neck pocket or bridge area on some model of guitar but this all depends on the guitar itself.https://valleysound.co.za/product/s-s-s-tortoiseshell-3ply-strat-style-pickguard/* Color: Tortoiseshell* Material: 3ply PVC + Celloid* Thickness: 2.35mm* Pickup rout: SSS single coil pickup route* Full size shielding aluminum foil on back* SSH/HSH/HH pickup rout pickguards available as well as other colors available.* Cut perfectly, with clean surface and smooth edge (sometimes pickguards may appear rough around the edges in pictures but this is just the protective plastic cover that peels off) -Pickguard screws sold separately
2y
VERIFIED
Successfully Added to List
View and manage your saved ads in your account.